Yamaha F30D Owner'S Manual Download | Manualshive

Page: 47 / 84

background image

Operation

42

3.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28080

Hydro tilt models

The outboard motor can be tilted up partially

to allow operation in shallow water.

WARNING

EWM00270

●

Place the gear shift in neutral before us-
ing the shallow water cruising system.

●

Run the boat at the lowest possible
speed when using the shallow water
cruising system.

●

Use extra care when operating in re-
verse. Too much reverse thrust can
cause the outboard motor to lift out of
the water, increasing the chance of ac-
cident and personal injury.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28174

Procedure for hydro tilt models

1.

Place the gear shift lever in neutral.

ZMU04072

DN

ZMU01936

UP

DN

DN

ZMU04073

ZMU04074

✩✪✰✬✤ ✧✥

«
...
45
46
47
48
49
...
»

Summary of Contents for F30D





















































































Reviews:

No comments

Related manuals for F30D

Brand: ON Semiconductor Pages: 5

Brand: Gigabyte Pages: 104

Brand: ASROCK Pages: 56

AnadigmApex AN231K04-DVLP3

Brand: Anadigm Pages: 16

Brand: ASROCK Pages: 160

Brand: Gigabyte Pages: 64

Brand: Acconeer Pages: 14

Brand: Gigabyte Pages: 88

BLKD955XBKLKR - 10PK 955X LGA775 8GB DDR2 16X

Brand: Intel Pages: 94

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 90

Brand: MSI Pages: 58

Brand: Atmel Pages: 74

Brand: Foxconn Pages: 106

Brand: DataExpert Pages: 44

Brand: DFI Pages: 64

Brand: Acer Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands