Yamaha F30D Owner'S Manual Download Page 19 | Manualshive

Page: 19 / 84

background image

Basic components

14

licensing or approval authority regula-

tions.

EMU25830

Fuel joint

This joint is used to connect the fuel line.

EMU25841

Fuel gauge

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

EMU25850

Fuel tank cap

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

EMU25860

Air vent screw

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

EMU26180

Remote control

The remote control lever actuates both the
shifter and the throttle. The electrical switch-
es are mounted on the remote control box.

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

1. Fuel joint
2. Fuel gauge
3. Fuel tank cap
4. Air vent screw

ZMU02284

3

1

4

2

1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine stop lanyard switch
7. Throttle friction adjuster

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”
4. Shift
5. Fully closed

✩✪✰✬✤ ✤✧

«
...
17
18
19
20
21
...
»

Summary of Contents for F30D





















































































Reviews:

No comments

Related manuals for F30D

Brand: V2 ELETTRONICA Pages: 12

Brand: Yamaha Pages: 86

Brand: MPS Pages: 6

ATmega328P Xplained Mini

Brand: Microchip Technology Pages: 26

Brand: IBM Pages: 40

Brand: Advantech Pages: 3

DUOX Programmer

Brand: Fermax Pages: 99

Brand: BCM Pages: 3

Brand: Texas Instruments Pages: 6

Brand: Photonic Universe Pages: 6

Brand: Seanix Pages: 49

Brand: ITX SECURITY Pages: 18

Brand: ASROCK Pages: 162

NuMicro NuTiny-SDK-NUC505

Brand: Nuvoton Pages: 26

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 90

Brand: EPOX Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands