Yamaha F30D Owner'S Manual Download Page 46 | Manualshive

Page: 46 / 84

background image

Operation

41

sure.

5.

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

CAUTION:

ECM00250

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

EMU28041

Procedure for tilting down (manual
and hydro tilt models)

1.

Release the tilt lock lever.

2.

Hold the rear of the top cowling with one
hand, tilt the outboard motor up slightly
and pull out the tilt support knob or re-
turn the tilt support lever.

3.

Slowly tilt the outboard motor down.

4.

Place the tilt lock lever in the lock posi-
tion.

EMU28052

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

2.

Release the tilt support lever or pull out
the tilt support knob.

ZMU04069

ZMU04070

ZMU04071

✩✪✰✬✤ ✧✤

«
...
44
45
46
47
48
...
»

Summary of Contents for F30D





















































































Reviews:

No comments

Related manuals for F30D

Brand: V2 ELETTRONICA Pages: 12

Brand: Biostar Pages: 53

Brand: Safran Pages: 26

Brand: JETWAY Pages: 41

Brand: Nematron Pages: 47

Brand: BCM Pages: 3

Brand: MSI Pages: 22

DQ963FX - Desktop Board Motherboard

Brand: Intel Pages: 72

Brand: Gigabyte Pages: 40

Brand: Intel Pages: 36

Brand: Microchip Technology Pages: 30

Brand: ST Pages: 14

Brand: ON Semiconductor Pages: 5

Brand: Laird Pages: 17

Brand: SOYO Pages: 93

Brand: ICP Pages: 44

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands