Yamaha F30D Owner'S Manual Download Page 28

Page: 28 / 84

Basic components

switch panel).

If the warning system has activated, stop the
engine and check the cooling water inlet for
clogging.

EMU30164

Low oil pressure warning

If the oil pressure drops too low, the warning
device will activate.
Activation of warning device

●

The engine speed will automatically de-
crease to about 2000 r/min.

●

The low oil pressure warning indicator will
light.

●

The buzzer will sound (if equipped on the
tiller handle, remote control box, or main
switch panel).

If the warning system has activated, stop the
engine as soon as it is safe to do so. Check
the oil level and add oil as needed. If the oil
level is correct and the warning device does
not switch off, consult your Yamaha dealer.

CAUTION:

ECM00100

Do not continue to run the engine if the

ZMU04587

ZMU04105

✩✪✰✬✤ ✥✦

Summary of Contents for F30D





















































































Search results

Summary of Contents for F30D

Reviews:

Related manuals for F30D

Brands by name

Popular brands

Yamaha F30D, Owner'S Manual

Search results

Summary of Contents for F30D

Reviews:

Related manuals for F30D

Brands by name

Popular brands