Yamaha F250B Owner'S Manual Download Page 85

Page: 85 / 122

Operation

Models equipped with trim rods: Once the
outboard motor is supported with the tilt
support lever, press the power trim and
tilt switch “

” (down) to retract the trim

rods.

NOTICE:

Be sure to retract the

trim rods completely during mooring.
This protects the rods from marine
growth and corrosion which could
damage the power trim and tilt mecha-
nism.

[ECM00251]

EMU35513

Procedure for tilting down (power trim
and tilt models)

The main switch must be “

” (on) for the

power trim and tilt switch on the digital
electronic control to operate.

Push the power trim and tilt switch “

”

(up) until the outboard motor is supported
by the tilt rod and the tilt support lever be-
comes free.

Release the tilt support lever.

Push the power trim and tilt switch “

”

(down) to lower the outboard motor to the
desired position.

ZMU01884

ZMU06258

U6BR11E0.book Page 79 Friday, June 13, 2008 3:43 PM

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F250B



























































































































Search results

Summary of Contents for F250B

Reviews:

Brands by name

Popular brands

Yamaha F250B, Owner'S Manual

Search results

Summary of Contents for F250B

Reviews:

Brands by name

Popular brands