Yamaha F250B Owner'S Manual Download Page 4

Page: 4 / 122

Table of contents

Safety information............................. 1

Outboard motor safety .................... 1

Boating safety ................................. 2

Boating organizations...................... 4
Basic boating rules

(Rules of the road) ....................... 4

Steering and sailing rules and sound

signals............................................. 4

Rules when encountering vessels...... 5
Other special situations ...................... 6

General information .......................... 9

Identification numbers record .......... 9

Outboard motor serial number ........... 9
Digital electronic control serial

number............................................ 9

Key number ...................................... 10

Read manuals and labels.............. 11

Warning labels.................................. 11

Specifications and requirements... 14

Specifications ................................ 14
Installation requirements ............... 15

Boat horsepower rating .................... 15

Mounting motor ................................ 15

Digital electronic control

requirements .............................. 15

Battery requirements..................... 16

Specifications of Battery ...................  16
Mounting battery...............................  16
Multiple batteries ..............................  16

Propeller selection ........................ 16

Counter rotation models ................... 17

Start-in-gear protection .................  17
Engine oil requirements ................  17
Fuel requirements .........................  18

Gasoline ........................................... 18
Ring Free Fuel Additive .................... 18

Muddy or acidic water ...................  19
Anti-fouling paint ...........................  19
Motor disposal requirements.........  19
Emergency equipment ..................  19
Emission control information.........  19

North American models .................... 19
Star labels ........................................ 20

Components .................................... 22

Components diagram.................... 22

Digital electronic control ................... 26
Digital electronic control-active

indicator ........................................ 27

Digital electronic control-alert

indicator ........................................ 28

Control lever .....................................  29
Neutral interlock trigger ....................  29
Free throttle switch ...........................  30
Throttle friction adjuster ....................  31
Station selector switch......................  32
Engine selector switch......................  32
Engine shut-off cord (lanyard) and

clip................................................. 32

Main switch.......................................  34
Starter button....................................  35
Engine stop button ...........................  35
Power trim and tilt switch on digital

electronic control ........................... 36

Power trim and tilt switch on bottom

engine cowling .............................. 36

Power trim and tilt switches .............. 37

U6BR11E0.book Page 1 Friday, June 13, 2008 3:43 PM

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F250B



























































































































Search results

Summary of Contents for F250B

Reviews:

Yamaha F250B, Owner'S Manual, Page: 4 / 122

Search results

Summary of Contents for F250B

Reviews: