manualshive.com logo in svg

Yamaha F250B, Owner'S Manual, Page: 15 / 122

Share
Download
Yamaha F250B Owner'S Manual Download Page 15

General information

9

EMU25171

Identification numbers record

EMU25183

Outboard motor serial number

The outboard motor serial number is stamped
on the label attached to the port side of the
clamp bracket.
Record your outboard motor serial number in
the spaces provided to assist you in ordering
spare parts from your Yamaha dealer or for
reference in case your outboard motor is sto-
len.

EMU34942

Digital electronic control serial num-
ber

The digital electronic control serial number is
stamped on the label attached to the digital
electronic control box.
Record your digital electronic control serial
number in the spaces provided to assist you
in newly connecting the digital electronic con-
trol to the outboard motor.

TIP:

Consult your Yamaha dealer if you have any
questions concerning the digital electronic
control serial number.

1. Outboard motor serial number location

1. Digital electronic control serial number loca-

tion

1. Digital electronic control serial number loca-

tion

1. Digital electronic control serial number loca-

tion

ZMU06224

1

ZMU05885

1

ZMU05887

1

U6BR11E0.book  Page 9  Friday, June 13, 2008  3:43 PM

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F250B



























































































































Reviews:

No comments