Yamaha F250B Page 84 Owner'S Manual Download | Manualshive

Page: 84 / 122

background image

Operation

78

3.

Press the power trim and tilt switch “

”

(up) until the outboard motor has tilted up
completely.

4.

Set the tilt support lever to support the en-
gine.

WARNING! After tilting the out-

board motor, be sure to support it with
the tilt support knob or tilt support le-
ver. Otherwise the outboard motor
could fall back down suddenly if oil in
the power trim and tilt unit or in the
power tilt unit loses pressure.

[EWM00262]

NOTICE:

Do not use the tilt support le-

ver or knob when trailering the boat.
The outboard motor could shake
loose from the tilt support and fall. If
the motor cannot be trailered in the
normal running position, use an addi-
tional support device to secure it in
the tilt position. For more detailed in-
formation, see page 83.

[ECM01641]

ZMU06280

UP

ZMU05837

UP

UP

UP

ZMU05838

UP

UP

ZMU06020

U6BR11E0.book Page 78 Friday, June 13, 2008 3:43 PM

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
82
83
84
85
86
...
»

Summary of Contents for F250B



























































































































Reviews:

No comments

Related manuals for F250B

Brand: Danbit Pages: 70

Brand: Lantronix Pages: 8

Brand: u-blox Pages: 2

Brand: JETWAY Pages: 48

Brand: P&E Microcomputer Systems Pages: 38

Brand: Atmel Pages: 16

Brand: IEI Technology Pages: 17

Brand: MSI Pages: 91

Brand: Xilinx Pages: 31

Brand: Intersil Pages: 6

Brand: Socket Pages: 37

Brand: Gigabyte Pages: 34

R3288LC-2N Series

Brand: JETWAY Pages: 44

Brand: EPOX Pages: 55

Brand: Dynatem Pages: 57

Brand: Intel Pages: 36

LMQ61460EVM-400K

Brand: Texas Instruments Pages: 20

Brand: Maxtang Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands