Yamaha DX150B Owner'S Manual Download Page 9

Page: 9 / 124

1-2

EMU01385

EMISSION CONTROL

INFORMATION

EMU01386

NORTH AMERICAN MODELS

This

engine

conforms

U.S.

Environmental Protection Agency (EPA)
regulations for marine SI engines. See the
label affixed to your engine for details.

Approval label of Emission control
certificate

This label is attached to the bottom cowl-
ing.

Emission control information label

Existing Technology ; N/A

Manufactured date label

This label is attached to the clamp bracket
or the swivel bracket.

Manufactured date label

EMISSION CONTROL INFORMATION

ENGINE FAMILY :

THIS ENGINE CONFORMS TO 2001 U.S. EPA REGULATIONS FOR MARINE SI ENGINES.
FELs :
SPARK PLUG :

IDLE SPEED :

rpm IN NEUTRAL

SPARK PLUG GAP (mm) :

g/kw-hr

Manufactured:

108032

67N-9-14-1 2/28/02 10:12 AM Page 7

Summary of Contents for DX150B





























































































































Search results

Summary of Contents for DX150B

Reviews:

Related manuals for DX150B

Brands by name

Popular brands

Yamaha DX150B, Owner'S Manual

Search results

Summary of Contents for DX150B

Reviews:

Related manuals for DX150B

Brands by name

Popular brands