Yamaha DX150B Owner'S Manual Download Page 80

Page: 80 / 124

4-13

EMU00369

CHECKING FUEL SYSTEM

Gasoline (petrol) and its vapors are highly
flammable and explosive. Keep away
from sparks, cigarettes, flames or other
sources of ignition.

Check  the  fuel  line  for  leaks,  cracks,  or
malfunctions.  If  any  problem  is  found,  it
should  be  repaired  immediately  by
Yamaha dealer or other qualified mechan-
ic.

Checking points

Fuel system parts leakage.

Fuel hose joint leakage.

Fuel hose cracks or other damage.

Fuel connector leakage.

Leaking fuel can result in fire or explo-
sion.

Check for fuel leakage regularly.

If any fuel leakage is found, the fuel
system must be repaired by a qualified
mechanic. Improper repairs can make
the outboard unsafe to operate.

67N-9-14-4 2/28/02 10:17 AM Page 14

Summary of Contents for DX150B





























































































































Search results

Summary of Contents for DX150B

Reviews:

Related manuals for DX150B

Brands by name

Popular brands

Yamaha DX150B, Owner'S Manual

Search results

Summary of Contents for DX150B

Reviews:

Related manuals for DX150B

Brands by name

Popular brands