Yamaha DX150B Owner'S Manual Download Page 59 | Manualshive

Page: 59 / 124

background image

701043

N

F

N

R

701044

E

3-16

EMU00261

SHIFTING

w

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

c

C

To  change  the  shifting  position  from  for-
ward  to  reverse  or  vice-versa,  close  the
throttle  first  so  that  the  engine  idles  (or
runs at low speeds).

EMU00264

FORWARD

Pull  up  the  neutral  interlock  trigger  (If
equipped)  and  move  the  remote  control
lever  quickly  and  firmly  from  Neutral  to
Forward.

EMU00269

REVERSE

w

When operating in Reverse, go slowly. Do
not  open  the  throttle  more  than  half.
Otherwise,  the  boat  may  become  unsta-
ble,  which  could  result  in  loss  of  control
and an accident.

Pull  up  the  neutral  interlock  trigger  (If
equipped)  and  move  the  remote  control
lever  quickly  and  firmly  from  Neutral  to
Reverse.

67N-9-14-3 2/28/02 10:15 AM Page 17

«
...
57
58
59
60
61
...
»

Summary of Contents for DX150B





























































































































Reviews:

No comments

Related manuals for DX150B

Brand: Actel Pages: 2

Brand: AOpen Pages: 95

Brand: Aeroflex Pages: 20

Airborne WLNN-EK-DP55x

Brand: B&B Electronics Pages: 6

Brand: IBASE Technology Pages: 84

Brand: BESTEK Pages: 47

Brand: ICP Pages: 50

Brand: BCM Pages: 57

Brand: Biostar Pages: 210

Brand: NXP Semiconductors Pages: 4

Brand: Silicon Laboratories Pages: 13

Brand: M-tech Pages: 2

Brand: u-blox Pages: 23

Brand: Asus Pages: 84

Brand: Asus Pages: 49

FM2A75M-DGS R2.0

Brand: ASROCK Pages: 59

Brand: ECS Pages: 60

Brand: Texas Instruments Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands