Yamaha DX150B Owner'S Manual Download Page 104 | Manualshive

Page: 104 / 124

background image

ON

START

OFF

701026

E

301021

208036

5-7

EMU00430

Emergency Starting Engine

1)

Remove the top cowling.

301022

2)

Remove the flywheel cover.

3)

Prepare  the  engine  for  starting.  See
“STARTING ENGINE” for procedures.
Be  sure  the  engine  is  in  Neutral  and
that  the  lanyard  is  attached  to  the
engine stop switch.

4)

Turn  the  main  switch  to  START  and
back  to  OFF  several  times  to  inject
some fuel into the combustion cham-
bers,  then  put  the  switch  in  the  ON
position.

5)

Insert  the  knotted  end  of  the  emer-
gency  starter  rope  into  the  notch  in
the  flywheel  rotor  and  wind  the  rope
several turns clockwise.

6)

Give a strong pull straight out to
crank the engine. Repeat if necessary.

NOTE:

If the engine will not start with this proce-
dure, refer to “ENGINE FAILS TO OPER-
ATE”.

67N-9-14-5 2/28/02 10:17 AM Page 8

«
...
102
103
104
105
106
...
»

Summary of Contents for DX150B





























































































































Reviews:

No comments

Related manuals for DX150B

CYTVII-B-E-1M-SK

Brand: Cypress Pages: 19

Brand: Gigabyte Pages: 36

Brand: JETWAY Pages: 48

Brand: JETWAY Pages: 52

Brand: Xilinx Pages: 88

Brand: Infineon Pages: 20

Brand: IEI Technology Pages: 145

Brand: Advantech Pages: 5

MIC23031-4YMT EV

Brand: Micrel Pages: 8

Brand: Commell Pages: 49

MT9V113PACSTCH-GEVB

Brand: ON Semiconductor Pages: 5

ConnectCore 6UL SBC Pro

Brand: Digi Pages: 54

Brand: JETWAY Pages: 51

Brand: Texas Instruments Pages: 28

Brand: ASROCK Pages: 57

Brand: DFI Pages: 118

Brand: Analog Devices Pages: 20

Brand: Supero Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands