Yamaha DSP-AX2 Owner'S Manual Download Page 14 | Manualshive

Page: 14 / 71

background image

Introduction

Preparations

Basic Operation

Advanced

Operation

Additional

Information

Appendix

12

Hookups

Connecting Video Components

Before you connect any components, disconnect the power supply to all the components you plan to connect including this unit and
determine which jacks are for the left and right channels and for input and output. After you finish all hookups, check them again to make
sure they are correct.

■

About the video jacks

There are three types of video jacks. Video signals input through the

VIDEO

jacks are the conventional composite video signals. Video

signals input through the

S VIDEO

jacks are separated into luminance (Y) and color (C) video signals. The S-video signals achieve high

quality color reproduction.
Video signals input through the

COMPONENT VIDEO

jacks are separated into luminance (

Y

) and color difference (

P

B

/C

B

,

P

R

/C

R

) video

signals. The jacks are also separated into three for each signal. The labels of the component video jacks may be different depending on the
component (e.g. Y, C

B

, C

R

/ Y, P

B

, P

R

/ Y, B-Y, R-Y/ etc.). Component video signals provide the best quality in picture reproduction.

If your video component has an S-video output or component video output, you can
connect it to this unit. Connect the S-video signal output jack on your video
component to the

S-VIDEO

jack or connect the component signal output jacks on

your video component to the

COMPONENT VIDEO

jacks.

Notes:

• Each type of video jack works independently. Signals input through the composite video,

S-video, and component jacks are output through the corresponding composite video, S-
video, and component jacks respectively.

• Use a commercially available S-video cable when connecting to the

S VIDEO

jacks, and

commercially available video cables when connecting to the

COMPONENT VIDEO

jacks.

• When you are using the

COMPONENT VIDEO

jacks, check the details in the owner’s

manual that came with the component being connected.

Composite VIDEO jack

S VIDEO jack

COMPONENT VIDEO jacks

«
...
12
13
14
15
16
...
»

Summary of Contents for DSP-AX2








































































Reviews:

No comments

Related manuals for DSP-AX2

Brand: NAD Pages: 2

trans-nova 9505

Brand: Hafler Pages: 24

Brand: Hafler Pages: 9

Brand: Hafler Pages: 7

Brand: Hafler Pages: 21

Brand: Hafler Pages: 2

Brand: Harman Pages: 2

Brand: Harley Benton Pages: 12

Brand: Kathrein Pages: 8

Brand: Kathrein Pages: 8

Brand: NJS Pages: 8

Brand: NJS Pages: 8

Brand: Harman Kardon Pages: 8

Brand: Crest Audio Pages: 18

Brand: McIntosh Pages: 36

Brand: Crest Audio Pages: 2

MULTI-TASKER MT103-118

Brand: Altinex Pages: 11

Atlona AT-UHD-CAT-4ED

Brand: Panduit Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands