Yamaha DragStar XVS650A Owner'S Manual Download

Page: 63 / 86

PERIODIC MAINTENANCE AND MINOR REPAIR

6-26

●

KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.

To store the battery

1. If the model will not be used for

more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.

2. If the battery will be stored for more

than two months, check it at least
once a month and fully charge it if
necessary.

3. Fully charge the battery before in-

stallation.

4. After installation, make sure that

the battery leads are properly con-
nected to the battery terminals.

CAUTION:

ECA10630

●

Always keep the battery
charged. Storing a discharged
battery can cause permanent
battery damage.

●

To charge a sealed-type (MF)
battery, a special (constant-volt-
age) battery charger is required.
Using a conventional battery

charger will damage the battery.
If you do not have access to a
sealed-type (MF) battery charg-
er, have a Yamaha dealer
charge your battery.

EAU33400

Replacing the fuses

1. Parking lighting fuse

2. Fuse box

3. Main fuse
4. Spare main fuse

U5SCE1E0.book Page 26 Monday, September 8, 2003 11:32 AM

Summary of Contents for DragStar XVS650A























































































Search results

Summary of Contents for DragStar XVS650A

Reviews:

Related manuals for DragStar XVS650A

Brands by name

Popular brands

Yamaha DragStar XVS650A, Owner'S Manual

Search results

Summary of Contents for DragStar XVS650A

Reviews:

Related manuals for DragStar XVS650A

Brands by name

Popular brands