Yamaha DragStar XVS650A Owner'S Manual Download | Manualshive

Page: 48 / 86

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-11

6

EAU33380

Cleaning the air filter element

The air filter element should be cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
Clean the air filter element more fre-
quently if you are riding in unusually
wet or dusty areas.

1. Remove the air filter case cover by

removing the screws.

2. Pull the air filter element out.
3. Lightly tap the air filter element to

remove most of the dust and dirt,
and then blow the remaining dirt
out with compressed air as shown.
If the air filter element is damaged,
replace it.

4. Insert the air filter element into the

air filter case as shown.

CAUTION:

ECA10480

●

Make sure that the air filter ele-
ment is properly seated in the
air filter case.

●

The engine should never be op-
erated without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.

5. Install the air filter case cover by

aligning the match marks and in-
stalling the screws.

1. Air filter case cover

2. Screw

1. Air filter element

1. Air filter element holder

2. Projection
3. Slot

1. Match marks

U5SCE1E0.book Page 11 Monday, September 8, 2003 11:32 AM

«
...
46
47
48
49
50
...
»

Summary of Contents for DragStar XVS650A























































































Reviews:

No comments

Related manuals for DragStar XVS650A

Brand: KAYO MOTOR Pages: 84

Brand: R&G Pages: 8

Brand: hepco & becker Pages: 2

Brand: MRA Pages: 9

Brand: yasuni Pages: 9

Brand: DYNATEK Pages: 4

Brand: BMW Pages: 160

R 1200 RT - 2006

Brand: BMW Pages: 194

Brand: BMW Pages: 223

Brand: BMW Pages: 169

Brand: BMW Pages: 133

Brand: BMW Pages: 8

Brand: BMW Pages: 153

F 650 GS DAKAR -

Brand: BMW Pages: 8

Brand: BMW Pages: 348

Brand: BMW Pages: 194

Brand: BMS Pages: 10

Brand: VESPA Pages: 308

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands