Yamaha DragStar XVS650A Owner'S Manual Download | Manualshive

Page: 50 / 86

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-13

6

NOTE:

If the specified idling speed cannot be
obtained as described above, have a
Yamaha dealer make the adjustment.

EAU21380

Adjusting the throttle cable
free play

The throttle cable free play should mea-
sure 4.0–6.0 mm (0.16–0.24 in) at the
throttle grip. Periodically check the
throttle cable free play and, if neces-
sary, have a Yamaha dealer adjust it.

EAU21400

Adjusting the valve clearance

The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.

1. Throttle stop screw

Engine idling speed:

1150–1250 r/min

1. Throttle cable free play

U5SCE1E0.book Page 13 Monday, September 8, 2003 11:32 AM

«
...
48
49
50
51
52
...
»

Summary of Contents for DragStar XVS650A























































































Reviews:

No comments

Related manuals for DragStar XVS650A

Brand: Can-Am Pages: 16

Brand: Can-Am Pages: 254

Brand: Yamaha Pages: 650

Brand: hepco & becker Pages: 4

Brand: N-Com Pages: 2

Brand: Memphis Shades Pages: 2

Brand: R&G Pages: 9

Brand: Suzuki Pages: 526

Brand: Cake Pages: 12

Brand: Romet Pages: 52

Brand: X-lite Pages: 96

Brand: PUIG Pages: 3

Brand: R&G Pages: 9

Brand: Baotian Pages: 30

Brand: Yadea Pages: 66

Brand: Indian Motorcycle Pages: 2

Brand: Honda Pages: 185

350 BULLET 1956

Brand: Royal Enfield Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands