Yamaha DragStar XVS650A Owner'S Manual Download

Page: 27 / 86

INSTRUMENT AND CONTROL FUNCTIONS

3-13

EAU14481

Storage compartment

The storage compartment is located on
the left side of the vehicle.

To open the storage compartment

1. Slide the lock cover open, insert

the key into the lock, and then turn
it clockwise.

2. Pull the storage compartment cov-

er out as shown.

To close the storage compartment

1. Place the storage compartment

cover in its original position as
shown.

2. Turn the key counterclockwise, re-

move it, and then close the lock
cover.

EAU14860

Adjusting the shock absorber
assembly

This shock absorber assembly is
equipped with a spring preload adjust-
ing ring.

CAUTION:

ECA10100

Never attempt to turn an adjusting
mechanism beyond the maximum or
minimum settings.

Adjust the spring preload as follows.

1. Remove the passenger and rider

seats. (See page 3-11.)

1. Storage compartment cover

2. Storage compartment lock cover

3. Storage compartment lock

1. Storage compartment
2. Storage compartment cover

1. Position indicator

2. Spring preload adjusting ring
3. Extension bar

4. Special wrench

U5SCE1E0.book Page 13 Monday, September 8, 2003 11:32 AM

Summary of Contents for DragStar XVS650A























































































Search results

Summary of Contents for DragStar XVS650A

Reviews:

Related manuals for DragStar XVS650A

Brands by name

Popular brands

Yamaha DragStar XVS650A, Owner'S Manual

Search results

Summary of Contents for DragStar XVS650A

Reviews:

Related manuals for DragStar XVS650A

Brands by name

Popular brands