Yamaha DG100-212, Owner'S Manual

Page: 7 / 32

7
■
Rear Panel
STATUS
DATA/CTRL BANK MSB/MAX
BANK LSB/MIN
TOGGLE ON-OFF
/NUMBER OF PGM
DEC
/NO INC
/YES
MEMORY
EDIT
PC
EDIT
WRITE
/EXIT ± 10
8.8.8
.
!8 !9 @0 @1 @3 @2 @4 @5
The Panel Controls
Before making any connections, make sure that the power on the DG100-212
and any external devices is switched
OFF .
DG100-212 internal speaker
or
a speaker with an impedance
of 4-8
Ω
and can handle
100W or more.
Store data from the
DG100-212’s
internal memory to
a MIDI device.
External Effector
MIDI IN MIDI OUT
IN OUT
Mixer or additional amp
A MIDI Controller
can be used to
select memory and
control volume.
!8
Speaker Jack (SPEAKER)
This jack connects the internal speaker to the internal amp. If neces-
sary, you can disconnect the internal speaker and connect an external
speaker to this jack.
If an external speaker is used, make sure that the speaker meets the
following requirements.
• 100W or more power capacity, and an impedance of 4 – 8
Ω
.
!9
MIDI OUT Jack
Connect this jack to the MIDI IN jack of a device that can save MIDI
data. The data stored in the DG100-212’s internal memory can then be
transmitted to an external MIDI device for storage. (
→
page 11: MIDI
Bulk Out)
Also, transmits MIDI data received by the MIDI IN jack
@0
, to an external
device when MIDI Merge is set to ON. (
→
page 11.)
@0
MIDI IN Jack
Connect this jack to a MIDI Foot Controller’s MIDI OUT jack, and the
external foot controller can be used to control the DG100-212. Memory
selection, volume control, reverb and echo ON/OFF can all be controlled
via an external foot controller. (
→
page 10.)
Also, memory data stored in an external storage device can be re-loaded
into the DG100-212’s internal memory. (
→
page 11 MIDI Bulk In)
@1
Effect Blend Control (EFFECT BLEND)
@2
Effect Send Jack (EFFECT SEND)
@3
Effect Return Jack (EFFECT RETURN)
An external effector can be inserted into the signal circuit between the
SEND/RETURN jacks. This allows further processing of the tone signal,
created by the main unit, by an external effector. Use the BLEND knob
to control the balance level between the external effector’s sound (EF-
FECT) and the sound created by the DG100-212 (DRY). Rotating the
knob fully to the EFFECT position allows only the sound produced by
the external effector to be heard. Rotating the knob fully to the DRY
position allows only the internal sound created by the amp to be heard,
without the added coloration of the external effector.
* Connecting a plug to the RETURN jack disconnects the internal circuit. The
signal returning from the effector enters the internal circuit here, where it
goes on to the power amp
→
speaker. When the RETURN jack is not in use,
the BLEND knob will have no affect.
Also, the SEND jack can function as a pre-out jack, and the RETURN jack
can function as a main-in jack.
@4
Line Out Jack (LINE OUT)
@5
Line Out Level Control (LINE OUT LEVEL)
The same signal that is sent to the speaker output jack
!8
, is also sent
to the LINE OUT jack at a line level (+4dBm/600
Ω
). The amp also has
an internal Speaker Simulator (can be switched ON/OFF
→
page 11.),
the output level can be controlled with the LINE OUT LEVEL knob. The
line signal can be sent to a mixer and can be used as an output jack to
an external amp.