7
CLP-265GP
4.
Circuit Boards & Assemblies (Main Unit)
(Time required: About 6 minutes each)
4-1
Remove the top board assembly (L) . (See procedure 2.)
4-2
Remove the top board assembly (S). (See procedure 3.)
4-3
Each circuit board and assembly can be removed by
removing its fixing screws as shown in table1. (Fig.4, Table 1)
5.
Key Cover Assembly
(Time required: About 6 minutes)
5-1
Remove the top board assembly (L) . (See procedure 2.)
5-2
Remove the top board assembly (S). (See procedure 3.)
5-3
Remove the screw marked [S03] for each side.
The rack covers L and R can then be removed. (Fig.5)
5-4
Set both ends of the rod to the slits of the rack and then
lift the rear portion of the key cover assembly. (Fig.6)
5-5
Lean the key cover assembly slightly, and remove the
guide pins from the guide rail. At that time, it is noted
not to damage the side cover. (Fig.6)
*
When assembling, be sure not to make scratches on the
side cover assembly.
*
When assembling, set both ends of the rod to the slits of
the rack accurately.
Rack Cover
L
[S03]
Key Cover Assembly
(Fig.5)
[S03]: Bind Head Tapping Screw-B 3.0X8 MFZN2W3 (WE774300)
Key Cover Assembly
Arm Assembly
Key Cover Assembly
6.
AJACK & DJACK Circuit Boards
(Time required: About 7 minutes)
6-1
Remove the top board assembly (L) . (See procedure 2.)
6-2
Remove the top board assembly (S). (See procedure 3.)
6-3
Remove the jack assembly. (See procedure 4.)
6-4
AJACK Circuit Board
6-4-1
Remove the screw marked [4A]. (Fig.7)
6-4-2
Remove the two (2) hexagonal nuts marked [6] and the
two (2) washers marked [5]. (Fig.7)
6-4-3
Remove the two (2) screws marked [7A]. The AJACK
circuit board can then be removed from the jack
assembly. (Fig.7)
6-5
DJACK Circuit Board
6-5-1
Remove the three (3) screws marked [4B]. (Fig.7)
6-5-2
Remove the two (2) screws marked [7B]. The DJACK
circuit board can then be removed from the jack
assembly. (Fig.7)
7.
MA80S Circuit Board
(Time required: About 8 minutes)
7-1
Remove the top board assembly (L) . (See procedure 2.)
7-2
Remove the top board assembly (S). (See procedure 3.)
7-3
Remove the MA cover. (U model only)(See procedure 4.)
7-4
Remove the MA80S assembly. (See procedure 4.)
7-5
Remove the five (5) screws marked [1], the three (3)
screws marked [2] and the screw marked [3]. The
MA80S circuit board can then be removed from the
MA80S assembly. (Fig.8)
(Fig.6)
Jack Assembly
AJACK
DJACK
[4A]
[5] [6]
[7A]
[7A]
[4B]
[7B]
[7B]
(Fig.7)
[4A,B]: Bind Head Tapping Screw-B 3.0X8 MFZN2W3 (WE774300)
[5]:
Washer BLACK (VJ869400)
[6]:
Special Nut M12X14X2 P=1.0 (WF559900)
[7A,B]: Bind Head Tapping Screw-B 3.0X8 MFZN2W3 (WE774300)
