Yamaha 6Y8-2819V-00 Owner'S Manual Download Page 10 | Manualshive

Page: 10 / 36

background image

5

Cooling water/engine temperature
display

The cooling water/engine temperature indi-

cator (

) comes on and the cooling

water temperature or the engine tempera-
ture is shown in 6 levels.

When the engine overheats, the cooling

water/engine temperature indicator (

)

blinks to warn of the malfunction.

CAUTION:

• When the overheat warning comes on,

turn the engine off and check the cool-
ing water inlet for clogs.

• If you cannot locate and correct the

cause, consult a Yamaha dealer.

NOTE:

The cooling water/engine temperature dis-
play shows “L” for low and “H” for high.

Blinks

Cooling water/engine temperature display

«
...
8
9
10
11
12
...
»

Summary of Contents for 6Y8-2819V-00





































Reviews:

No comments

Related manuals for 6Y8-2819V-00

Brand: Yamaha Pages: 2

Brand: 3nh Pages: 10

Brand: Kanomax Pages: 26

Brand: Macnaught Pages: 20

Brand: Hama Pages: 16

STORA-ABG RKS-01

Brand: ECOTEST Pages: 146

Brand: Caen Pages: 63

Brand: Caen Pages: 35

Brand: Osaka Pages: 3

Brand: SIKA Pages: 8

Brand: LaserLiner Pages: 64

Brand: LaserLiner Pages: 84

Brand: NARDA Pages: 14

Brand: Ahlborn Pages: 32

Brand: Texmate Pages: 15

Brand: Doepke Pages: 2

Brand: Vortex Pages: 11

Brand: Roland Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands