Yamaha 6Y8-2819V-00 Owner'S Manual Download Page 3

Page: 3 / 36

The Command Link Multifunction Meter
enables the display of information through
digital communication with the engine.

Optional parts such as the speed sensor,
cooling water pressure sensor, Triducer-
Multi sensor, and GPS are described in this
manual by assuming that the parts are
installed and set up on the outboard motor.

The Command Link Multifunction Meter
described in this manual consists of the fol-
lowing.

• Tachometer unit

(Part No.: 6Y8-8350T-1*)

• Speed & Fuel meter unit

(Part No.: 6Y8-83500-1*)

The Command Link Multifunction Meter is
compatible with the following outboard
motors.

4-stroke models:
Fuel injection models only
2-stroke models:
HPDI models only

The operations of the set button and the
mode button are described in this manual as
follows.

Button operations:

•

Press the set button one time.

•

Press the mode button one time.

•

Press the set button or the mode button
one time.

•

(1 second)

Press the set button for 1 second.

•

(4 seconds)

Press the mode button for 4 seconds.

•

(10 seconds)

Press the set button for 10 seconds.

•

(1 second) (2 times)

Press the mode button two times, 1 sec-
ond each time.

•

Press the set button and the mode button
simultaneously.

•

(1 second)

Press the set button and the mode button
simultaneously for 1 second.

Summary of Contents for 6Y8-2819V-00





































Search results

Summary of Contents for 6Y8-2819V-00

Reviews:

Related manuals for 6Y8-2819V-00

Brands by name

Popular brands

Yamaha 6Y8-2819V-00, Owner'S Manual

Search results

Summary of Contents for 6Y8-2819V-00

Reviews:

Related manuals for 6Y8-2819V-00

Brands by name

Popular brands