Yamaha 2008 YZF-R1X Page 75 Owner'S Manual Download | Manualshive

Page: 75 / 108

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-26

6

4. If the drive chain slack is incorrect,

adjust it as follows.

EAU34311

To adjust the drive chain slack

1. Loosen the axle nut and the lock-

nut on each side of the swingarm.

2. To tighten the drive chain, turn the

adjusting bolt on each side of the
swingarm in direction (a). To loos-
en the drive chain, turn the adjust-
ing bolt on each side of the
swingarm in direction (b), and then
push the rear wheel forward.

NOTE:

Using the alignment marks on each
side of the swingarm, make sure that
both chain pullers are in the same posi-
tion for proper wheel alignment.

CAUTION:

ECA10570

Improper drive chain slack will over-
load the engine as well as other vital
parts of the motorcycle and can lead
to chain slippage or breakage. To
prevent this from occurring, keep
the drive chain slack within the
specified limits.

3. Tighten the locknuts, then the axle

nut to their specified torques.

1. Drive chain slack

1. Axle nut

2. Drive chain slack adjusting bolt
3. Locknut

4. Alignment marks

Tightening torques:

Locknut:

16 Nm (1.6 m·kgf, 11 ft·lbf)

Axle nut:

150 Nm (15.0 m·kgf, 110 ft·lbf)

U4C821E0.book Page 26 Tuesday, July 17, 2007 11:37 AM

«
...
73
74
75
76
77
...
»

Summary of Contents for 2008 YZF-R1X













































































































Reviews:

No comments

Related manuals for 2008 YZF-R1X

Indian eFTR Mini 2021

Brand: Razor Pages: 20

Brand: hepco & becker Pages: 4

Brand: Qlink Pages: 44

X-903 Ultra Carbon 29

Brand: X-lite Pages: 116

Freeride E-XC 2019

Brand: KTM Pages: 44

Brand: OKBABY Pages: 35

GT650SR - PARTS CATALOGUE

Brand: HYOSUNG Pages: 124

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 134

Brand: Yamaha Pages: 134

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands