Yamaha 2008 YZF-R1X Owner'S Manual Download | Manualshive

Page: 85 / 108

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-36

6

WARNING

EWA10790

Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.

4. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

CAUTION:

ECA10650

Take care not to damage the follow-
ing parts:

●

Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.

●

Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.

5. Install the headlight bulb cover,

and then connect the coupler.

6. Install the panel.
7. Have a Yamaha dealer adjust the

headlight beam if necessary.

To replace a low beam headlight
bulb

1. Remove the headlight bulb cover

by turning it counterclockwise.

2. Disconnect the headlight coupler.

3. Unhook the headlight bulb holder,

and then remove the defective
bulb.

1. Do not touch the glass part of the bulb.

1. Headlight bulb cover

1. Headlight coupler

U4C821E0.book Page 36 Tuesday, July 17, 2007 11:37 AM

«
...
83
84
85
86
87
...
»

Summary of Contents for 2008 YZF-R1X













































































































Reviews:

No comments

Related manuals for 2008 YZF-R1X

Brand: LAZER Pages: 13

Brand: BMW Pages: 288

Brand: hepco & becker Pages: 3

Brand: Miller Pages: 22

Brand: Öhlins Pages: 2

Brand: hepco & becker Pages: 4

Brand: Yamaha Pages: 39

Roadliner XV1900AV

Brand: Yamaha Pages: 86

ROADLINER XV19C

Brand: Yamaha Pages: 95

Brand: Yamaha Pages: 70

Road Star XV1600AT 2004

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 72

Road Star XV17ASX

Brand: Yamaha Pages: 110

Road Star XV1600A 2000

Brand: Yamaha Pages: 103

Road Star XV16AMC

Brand: Yamaha Pages: 110

ROAD STAN XV17AC

Brand: Yamaha Pages: 105

Brand: Yamaha Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands