Yamaha 2008 YZF-R1X Owner'S Manual Download

Page: 61 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-12

2. Start the engine, warm it up for

several minutes, and then turn it
off.

3. Place an oil pan under the engine

to collect the used oil.

4. Remove the engine oil filler cap

and drain bolt to drain the oil from
the crankcase.

NOTE:

Skip steps 5–7 if the oil filter cartridge is
not being replaced.

5. Remove the oil filter cartridge with

an oil filter wrench.

NOTE:

An oil filter wrench is available at a
Yamaha dealer.

6. Apply a thin coat of engine oil to

the O-ring of the new oil filter car-
tridge.

NOTE:

Make sure that the O-ring is properly
seated.

7. Install the new oil filter cartridge

with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.

1. Engine oil drain bolt

1. Oil filter wrench
2. Engine oil filter cartridge

1. O-ring

U4C821E0.book Page 12 Tuesday, July 17, 2007 11:37 AM

Summary of Contents for 2008 YZF-R1X













































































































Search results

Summary of Contents for 2008 YZF-R1X

Reviews:

Related manuals for 2008 YZF-R1X

Brands by name

Popular brands

Yamaha 2008 YZF-R1X, Owner'S Manual

Search results

Summary of Contents for 2008 YZF-R1X

Reviews:

Related manuals for 2008 YZF-R1X

Brands by name

Popular brands