Yamaha 2008 YZF-R1X Owner'S Manual Download | Manualshive

Page: 72 / 108

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-23

6

NOTE:

If the specified clutch lever free play
cannot be obtained as described
above, proceed as follows.

1. Fully turn the adjusting bolt at the

clutch lever in direction (a) to loos-
en the clutch cable.

2. Loosen the locknut at the crank-

case.

3. To increase the clutch lever free

play, turn the adjusting nut in direc-
tion (a). To decrease the clutch le-
ver free play, turn the adjusting nut
in direction (b).

4. Tighten the locknut.

EAU22270

Adjusting the rear brake light
switch

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the adjusting nut while holding the
rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a). To
make the brake light come on later, turn
the adjusting nut in direction (b).

EAU22390

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU43062

Front brake pads

The front brake calipers are equipped
with two sets of brake pads.
Each front brake pad is provided with
one or two wear indicator grooves,
which allow you to check the brake pad
wear without having to disassemble the
brake. To check the brake pad wear,
check the wear indicator grooves. If a
brake pad has worn to the point that a

1. Locknut

2. Clutch lever free play adjusting nut (crank-

case)

1. Rear brake light switch

2. Rear brake light switch adjusting nut

1. Brake pad wear indicator groove

U4C821E0.book Page 23 Tuesday, July 17, 2007 11:37 AM

«
...
70
71
72
73
74
...
»

Summary of Contents for 2008 YZF-R1X













































































































Reviews:

No comments

Related manuals for 2008 YZF-R1X

Brand: Ohlins Pages: 4

CoreManual TorqDrive

Brand: Rekluse Pages: 20

Brand: RPS Pages: 28

Brand: Nuviz Pages: 46

Operation and Instruction Manua

Brand: Takegawa Pages: 9

Brand: KC Pages: 32

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

Brand: Maat Pages: 12

Brand: Suzuki Pages: 24

Brand: Suzuki Pages: 31

Brand: Suzuki Pages: 74

Brand: Suzuki Pages: 37

Brand: Suzuki Pages: 125

Brand: Suzuki Pages: 353

Brand: Suzuki Pages: 355

Brand: Suzuki Pages: 352

Brand: Suzuki Pages: 399

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands