manualshive.com logo in svg

Yamaha 2006 FJR1300AS, Service Manual

Share
Download
Yamaha 2006 FJR1300AS Service Manual Download Page 55

SHAFT DRIVE

– 46 –

EAS23550

SHAFT DRIVE

EAS23660

INSTALLING THE DRIVE SHAFT AND FINAL 
DRIVE ASSEMBLY

1. Lubricate:

• Drive shaft spline (final drive pinion gear side)

2. Lubricate:

• Drive shaft spline (universal joint side)

3. Install:

• Oil seal “1” 
• Washer “2”

(with the fork seal driver weight “3” and fork 
seal driver attachment “4”)

4. Install:

• Circlip 

5. Install:

• Drive shaft “1”

(to the final drive pinion gear)

• Oil seal “2”

(to the final gear case with the fork seal driver 
weight “3” and oil seal installing tool “4”)

6. Install:

• Universal joint
• Final drive assembly

NOTE:

Align the drive shaft splines with the driven yoke 
of the universal joint.

7. Tighten:

• Final drive assembly nuts

8. Install:

• Sidestand
• Left footrest assembly

Refer to “SHIFT ACTUATOR AND SHIFT 
ROD” on page 57.

9. Install:

• Rear wheel

Refer to “REAR WHEEL” in chapter 4. (Man-
ual No.: 3P6-28197-E0)

10.Fill:

• Final gear case

Refer to “CHECKING THE FINAL GEAR OIL 
LEVEL” in chapter 3. (Manual No.: 3P6-
28197-E0)

 

Recommended lubricant

Molybdenum disulfide grease

 

Recommended lubricant

Lithium-soap-based grease

 

Fork seal driver weight

90890-01184

Fork seal driver attachment

90890-01186

Replacement 27 mm

YM-A9409-1

 

Fork seal driver weight

90890-01184

Oil seal installing tool

90890-01512

New

3

4

1

2

New

New

 

Installed depth “a”

8.5–10.0 mm (0.33–0.39 in)

T

 

R

.

.

 

Final gear case nut

42 Nm (4.2 m·kg, 30 ft·lb)

3

1

4

2

a

Summary of Contents for 2006 FJR1300AS























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands