manualshive.com logo in svg

Yamaha 2006 FJR1300AS, Service Manual

Share
Download
Yamaha 2006 FJR1300AS Service Manual Download Page 29

CABLE ROUTING

– 20 –

1. Auxiliary DC jack
2. Left radiator fan motor lead
3. Accessory box solenoid
4. Wire harness
5. Front cowling wire harness
6. Radiator inlet hose
7. Grip warmer control unit leads
8. Left radiator fan
9. Coolant reservoir breather hose
10. Left horn (low)
11. Left horn (low) leads
12. Thermostat assembly breather hose
13. Joint coupler
A. Fasten the handlebar switch leads, hand shift 

switch lead, and grip warmer leads to the front 
cowling wire harness with a plastic locking tie. 
Face the end of the plastic locking tie rearward, 
along the side of the accessory box. Do not cut off 
the excess end of the plastic locking tie.

B. Fasten the wire harness and left radiator fan motor 

lead with the holder.

C. Route the grip warmer control unit leads to the 

outside of the thermostat assembly breather hose.

D. Fasten the front cowling wire harness to the 

radiator inlet hose with a plastic locking tie, making 
sure to install the tie on the harness’ protective 
sleeve, and then cut off the excess end of the tie.

E. After connecting the couplers, cover them 

completely with the cover, and then push them in 
between the radiator inlet hose and the thermostat 
inlet hose 2.

Summary of Contents for 2006 FJR1300AS























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands