Yamaha 2006 FJR1300AS Service Manual Download Page 141

Page: 141 / 150

ELECTRICAL COMPONENTS

– 132 –

Second step:

Radiator fan motor relay

EAS28240

CHECKING THE YCC-S SPEED SENSOR

1. Check:

• YCC-S speed sensor output voltage

Out of specification

→

Replace.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the pocket tester (DC 20 V) to the

YCC-S speed sensor coupler (wire harness
side) as shown.

b. Turn the main switch to “ON”.
c. Elevate the rear wheel and slowly rotate it.
d. Measure the voltage of white/yellow and

black/blue. With each full rotation of the rear
wheel, the voltage reading should cycle from
0.6 V to 4.8 V to 0.6 V to 4.8 V.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

ET2D21022

CHECKING THE GEAR POSITION SENSOR

1. Remove:

• Gear position sensor

NOTE:

Remove only the screws “1” when removing the
gear position sensor. Do not remove the screws
“2”.

2. Check:

• Gear position sensor maximum resistance

Out of specification

→

Replace the gear posi-

tion sensor.

Result

No continuity

(between “1” and “2”)

1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe

Result

Continuity

(between “3” and “4”)

1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe

Result

Continuity

(between “3” and “4”)

Output voltage reading cycle

0.6 V to 4.8 V to 0.6 V to 4.8 V

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

white/yellow “1”

• Negative tester probe

→

black/blue “2”

W L

L W

Summary of Contents for 2006 FJR1300AS























































































































































Search results

Summary of Contents for 2006 FJR1300AS

Reviews:

Brands by name

Popular brands

Yamaha 2006 FJR1300AS, Service Manual

Search results

Summary of Contents for 2006 FJR1300AS

Reviews:

Brands by name

Popular brands