background image

36

P/N: 11854801   REV. AC

   September 2017

PARTS LIST

PARTS LIST

The parts lists and illustrations in this section of the manual cover 

parts for models of YALE “LodeKing LT” Electric hoists. A typical 

hoist is shown as the basis for the exploded parts illustrations;

therefore, certain variations may occur from the information given. 

For this reason, always correspond with:

1.  Hoist Model Number from identification plate.
2.  Serial number of the hoist stamped below  

identification plate.

3.  Catalog Number
4.  Voltage, phase, hertz from the identification plate.
5.  Hoist Capacity
6.  Length of lift.
7.  Part number of part from parts list.
8.  Number of parts required.
9.  Part name from parts list.
10.  Hoist Serial Number.

Certain parts of your hoist will, in time, require replacement under 

normal wear conditions. Other items such as gaskets, fasteners, 

insulators, etc., may be damaged or lost during disassembly. It is 

suggested that these parts be purchased for your hoist as spares for 

future use. These parts are listed at the end of this manual.

The numbers assigned to parts of our various assemblies in our 

Parts List are the part numbers used in manufacturing. Some of 

these itemized parts are not for individual sale, but must be grouped 

with other related replacement items.

NOTICE

WHEN ORDERING PARTS OR INFORMATION ON THIS
EQUIPMENT, ALWAYS INCLUDE MODEL AND SERIAL
NUMBER ON ORDER.

Using “Commercial” or other manufacturer’s parts to repair 

LodeKing Hoists may cause load loss.

TO AVOID INJURY:
Use only YALE Hoist supplied parts. Parts may look alike but 

YALE Hoist parts are made of specific  

materials or processed to achieve specific properties.

LIST OF PART ILLUSTRATIONS

TITLE

FIGURE NO.

PAGE NO.

GEARBOX MOUNTING ASSEMBLY

7

37

RCLS GROUP ASSEMBLY

8

38

WHEEL BLOCK ASSEMBLY

9

39

10T UPPER REEVING ASSEMBLY

10

40

15T UPPER REEVING ASSEMBLY

11

41

20T & 25T UPPER REEVING ASSEMBLY  

12

42

DRUM & BEARING SUPPORT ASSEMBLY  

13

43

UPLS GROUP  ASSEMBLY

14

44

10T LOWER BLOCK ASSEMBLY

15

45

15T LOWER BLOCK ASSEMBLY  

16

46

20T/25T LOWER BLOCK ASSEMBLY 

17

47

SHEAVE COMPARISON

18

48

DECKMOUNT

19

49

Summary of Contents for Lodeking LT Series






















































Reviews: