HOIST
OPERATION & MAINTENANCE
10
P/N: 11854801 REV. AC
September 2017
COLUMBUS
McKINNON
C O R P O R A T I ON
Columbus McKinnon Corporation
Amherst, NY USA
NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFOR
MATION
A
8
7
6
8
7
6
5
4
3
2
1
B
C
D
B
C
D
2/3/2015
APCCE
45487403
1:16
HOIST ASSEMBLY
200MM WHEEL BLOCKS
15T LODEKING LT
RSMS
Modeled:
Drawn:
Approved:
Design Authority:
Original project:
Original scale:
Format
B
Number:
Hoist PDE
Hoist PDE
2/3/2015
Dimensional Units
INCH
Sheet
Third Angle Projection
Description:
1
1
-
-
-
-
ECN
-
-
Rev.
-
Description of change
Date
-
-
By
-
-
-
-
-
-
Material:
Columbus McKinnon Corporation
Hoist & Rigging - Americas
Amherst, NY USA
Material No:
Standard:
Standard Dimensional
Tolerances Unless
Otherwise Specified
0" to 60" Over 60"
.X .020 .025
.XX .010 .015
.XXX .005 .010
Ang 0 30' 0 30'
Columbus McKinnon Corporation (CMCO) claims proprietary rights
in the material disclosed hereon. This drawing and/or technica
l information is issued in
confidence for engineering information only and may not be repr
oduced or used to manufacture anything shown or referred to her
eon without direct
permission from CMCO to the user. This drawing and/or technica
l information is loaned for mutual assistance and is subject to
recall by CMCO at any time.
This drawing and/or technical information is the property of CM
CO.
COLUMBUS
McKINNON
C O R P O R A T I ON
Columbus McKinnon Corporation
Amherst, NY USA
NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFOR
MATION
A
8
7
6
8
7
6
5
4
3
2
1
B
C
D
B
C
D
2/3/2015
APCCE
45487403
1:24
HOIST ASSEMBLY
200MM WHEEL BLOCKS
15T LODEKING LT
RSMS
Modeled:
Drawn:
Approved:
Design Authority:
Original project:
Original scale:
Format
B
Number:
Hoist PDE
Hoist PDE
2/3/2015
Dimensional Units
INCH
Sheet
Third Angle Projection
Description:
1
1
-
-
-
-
ECN
-
-
Rev.
-
Description of change
Date
-
-
By
-
-
-
-
-
-
Material:
Columbus McKinnon Corporation
Hoist & Rigging - Americas
Amherst, NY USA
Material No:
Standard:
Standard Dimensional
Tolerances Unless
Otherwise Specified
0" to 60" Over 60"
.X .020 .025
.XX .010 .015
.XXX .005 .010
Ang 0 30' 0 30'
Columbus McKinnon Corporation (CMCO) claims proprietary rights
in the material disclosed hereon. This drawing and/or technica
l information is issued in
confidence for engineering information only and may not be repr
oduced or used to manufacture anything shown or referred to her
eon without direct
permission from CMCO to the user. This drawing and/or technica
l information is loaned for mutual assistance and is subject to
recall by CMCO at any time.
This drawing and/or technical information is the property of CM
CO.
REEVING TYPES
Yale powered wire rope hoists and winches are reeved in various
ways to gain desired advantages. Proper reeving insures maximum
life of the hoist drum, wire rope, and bottom block assembly while
obtaining the best characteristics of capacity, lift, and speed for the
basic unit.
Reeving is “double”, i.e. two ropes coming from the drum. Close
headroom hoists are double reeved. “Part” designates the number
of times the rope runs between the hoist and bottom block.
For example: With 2 part double reeving, the rope runs from the rope
drum to the bottom block, up to the equalizer sheave, back to the
bottom block, then back to the rope drum, indicating 4 “parts” of
rope supporting the load.
The drawings below show the characteristics of each principal
method of reeving.
Advantages of double reeved units include minimum lateral hook
drift (keeping load in the same approximate position in relation to
the drum and beam) and a lower hoist headroom requirement.
4 PART REEVING
10 TON CAPACITY
8 PART REEVING
20 & 25 TON CAPACITY
6 PART REEVING
15 TON CAPACITY
Summary of Contents for Lodeking LT Series
Page 50: ...NOTES ...
Page 51: ...NOTES ...
