Yale Lodeking LT Series Page 11 Operating & Maintenance Manual Download

Page: 11 / 53

HOIST

OPERATION & MAINTENANCE

P/N: 11854801 REV. AC

September 2017

LUBRICANT SPECIFICATIONS

AMBIENT TEMPERATURE

-20º to +50º F (-29 to +10ºC)

50º to 125º F (10º to 52ºC)

125º to 250ºF (52º to 121ºC)

No Speciﬁcation

Cable Lubricant

Wire Rope Lubricant

Amoco® Oil Co.

------------------------------------------ Amovis® 5-X ------------------------------------------

Mobil® Oil Corp.

---------------------------------------- Mobilarma® 798 ----------------------------------------

Sun® Oil Corp.

-------------------------------- Sunoco® Wire Robe Lubricant --------------------------------

Texaco® Inc.

Crater A

Texclad® 2

AGMA Lubricant

No. 1

No. 2

General Oil

General Oiling to Prevent Rust-

ing an Provide Limited Lubrica-

tion for Points Not Considered

Normal Wear Points

Viscosity @ 100º F

193-235 SUS

284-347 SUS

Viscosity Index

60 Min.

Pour Point

-20ºF (-29ºC)

10ºF (-12ºC)

Amoco® Oil Co.

Rykon® Oil 46

American Industrial Oil® 68

Mobil® Oil Corp.

--------------------------------------Mobil® DTE Oil Heavy--------------------------------------

Shell® Oil Co.

Rotella® 10W

Rotella® 10W-30

Sun® Oil Co.

Sunvis® 932

Sunvis® 968

Texaco® Oil Inc.

Rando® Oil 46

Rando® Oil 68

MPG

NLGI Grease

No.1

No. 2

Multipurpose Grease

Grease Lubricated Wear

Points Provided

6ASTM Worked
Penetration

310-340

265-295

Dropping Point

360ºF (182ºC)

Base

Lithium

Amoco® Oil Co.

Amolith® Grease 1 EP

Amolith® Grease No. 2 EP

Mobil® Oil Corp.

Mobilith® AW1

Mobilith® AW 2

Shell® Oil Co.

------------------------------------------Retinax LC-----------------------------------------------

Sun® Oil Co.

Presitge® 741 EP

Sunoco® Multipurpose 2

Texaco Oil Inc.

Multifak® EP 1

Multifak® EP 2

Summary of Contents for Lodeking LT Series





















































Search results

Summary of Contents for Lodeking LT Series

Reviews:

Related manuals for Lodeking LT Series

Brands by name

Popular brands

Yale Lodeking LT Series, Operating & Maintenance Manual

Search results

Summary of Contents for Lodeking LT Series

Reviews:

Related manuals for Lodeking LT Series

Brands by name

Popular brands