background image

WARRANTY

WARRANTY AND LIMITATION OF REMEDY AND LIABILITY

Recommended Spare Parts for Your Shaw-Box Hoist

Certain parts of your hoist will, in time, require replacement under normal wear conditions.

It is suggested that the following parts be purchased for your hoist as spares for future use.

One set of load brake fiction washers
One set of motor brake washer and lining assemblies
One set of motor brake plates
One set of motor brake release springs
One motor brake actuator spring
One brake controller
One gearcase cover gasket
One brake cover gasket
One set of contactors
One transformer
One wire rope assembly

Note:  When ordering parts always furnish Hoist Serial Number, Catalog Nulmber, Motor Horsepower, Voltage,
Phase, Frequency and Rated Load of Hoist on which the parts are to be used.

Parts for your hoist are available from your local authorized Shaw-Box repair station.
For the location of your nearest repair station, write:

IN USA

Yale

!!!!!

Lift-Tech

P.O. Box 769
Muskegon, MI 49443-0769

Phone: 800 742-9269
Fax:

800 742-9270

A. Seller warrants that its products and parts, when shipped, and its
work (including installation, construction and start-up), when per-
formed, will meet applicable specifications, will be of good quality and
will be free from defects in material and workmanship. All claims for
defective products or parts under this warranty must be made in
writing immediately upon discovery and in any event, within one (1)
year from shipment of the applicable item unless Seller specifically
assumes installation, construction or start-up responsibility. All claims
for defective products or parts when Seller specifically assumes
installation, construction or start-up responsibility and all claims for
defective work must be made in writing immediately upon discovery
and in any event, within one (1) year from completion of the applicable
work by Seller, provided; however, all claims for defective products
and parts made in writing no later than eighteen (18) months after
shipment. Defective items must be held for Seller’s inspection and
returned to the original f.o.b. point upon request. THE ‘FOREGOING
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES WHATSO-
EVER, EXPRESS, IMPLIED AND STATUTORY, INCLUDING, WITH-
OUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANT-
ABILITY AND FITNESS.

B. Upon Buyer’s submission of a claim as provided above and its
substantiation, Seller shall at its option either (i) repair or replace its
product, part or work at either the original f.o.b. point of delivery or at
Seller’s authorized service station nearest Buyer or (ii) refund an
equitable portion of the purchase price.

C. This warranty is contingent upon Buyer’s proper maintenance and
care of Seller’s products, and does not extend to normal wear and
tear.  Seller reserves the right to void warranty in event of Buyer’s use
of inappropriate materials in the course of repair or maintenance, or
if Seller’s products have been dismantled prior to submission to Seller
for warranty inspection.

D. The foregoing is Seller’s only obligation and Buyer’s exclusive
remedy for breach of warranty and is Buyer’s exclusive remedy
hereunder by way of breach of contract, tort, strict liability or other-
wise.  In no event shall Buyer be entitled to or Seller liable for
incidental or consequential damages. Any action for breach of this
agreement must be commenced within one (1) year after the cause
of action has accrued.

Summary of Contents for SHAW-BOX





































































Reviews: