page 105
MARK-V FT-1000MP Operating Manual
8-6 uSEr-SEt
User Setting - This configures an operating “envi-
ronment” selected by pressing and holding in the front-
panel [PKT] button. Operating parameters are selected
using the Sub VFO knob, while the options are chosen
with the Main VFO knob.
Mode
- This selects to which mode the custom set-
tings are applied. Choose LSB, USB, CW (normal/
reverse), RTTY (normal/reverse), or packet (LSB
only).
Display Offset
- You can choose a custom offset
±5.000 kHz (in 5-Hz steps) to take effect when the
“USER” mode is activated. The default offset is de-
pendent upon operating mode.
Rx PLL Offset
- You can offset the receiver PLL
frequency ±5.000 kHz (in 5-Hz steps) when the
“USER” mode is activated.
Rx Carrier
- This is used to adjust the receive car-
rier injection frequency between 450 ~ 460 kHz. The
default injection frequency is dependent upon op-
erating mode.
Tx PLL Offset
- You can offset the transmitter PLL
frequency ±5.000 kHz (in 5-Hz steps) when the
“USER” mode is activated.
Tx Carrier
- This is used to adjust the transmit car-
rier injection frequency between 450.000 ~ 453.700
kHz or 456.300 ~ 460.000 kHz (PKT), 456.300 ~
460.000 kHz (LSB), 450.000 ~ 453.700 kHz (USB),
or between 450.000 ~ 460.000 kHz (all others). The
default injection frequency is dependent upon the
operating mode.
RTTY Offset (shift)
- For operators who desire to
use a non-standard mark/space shift (that is, other
than 170/425/850 Hz), a custom shift (±5.000 kHz
in 5-Hz steps) can be chosen. The mark is the car-
rier frequency, while the space is offset above or
below the carrier by the value of this setting. For
best results, we recommend limiting shift to ±1.000
kHz or less.
Easy Set
- If you enjoy operating FAX, SSTV, or
PSK-31, you can select on of these for the User
mode. The carrier and offset options for both set-
tings come factory pre-configured and optimized for
best operation.
Menu Selection and Settings
8-7 Sub-AGc
SUB VFO Receiver AGC - Selects automatic, slow,
or fast AGC recovery time for the Sub receiver.
8-8 tunEr
Antenna Tuner - Enables or disables the internal
automatic antenna tuner unit for operation.
8-9 cAr oFSt
Carrier Point Offset - This allows shifting the car-
rier point (IF passband) on both Tx and Rx to tailor the
received audio response, as well as your transmitted
voice audio. This can be used to customize your signal
for your own voice characteristics. Seven individual
carrier settings are selected with the Sub VFO dial,
while offsets are adjusted (in 10-Hz steps) using the
Main VFO dial:
Rx LSB Carrier
- Adjusts the receiver carrier point
for LSB throughout the range of –200 ~ +500 Hz.
Tx LSB Carrier
- Adjusts the transmitter carrier point
for LSB throughout the range of –200 ~ +500 Hz.
Processor LSB
- Adjusts the speech processor car-
rier point for LSB throughout the range of –200 ~
+500 Hz.
Rx USB Carrier
- Adjusts the receiver carrier point
for USB throughout the range of –200 ~ +500 Hz.
Tx USB Carrier
- Adjusts the transmitter carrier point
for USB throughout the range of –200 ~ +500 Hz.
Processor USB
- Adjusts the speech processor
carrier point for USB throughout the range of –200
~ +500 Hz.
Tx AM Carrier
- Adjusts the transmitter carrier point
for AM throughout the range of ±3000 Hz.
Note
: See the table on the next page for a com-
plete list of filter offsets according to mode, and cus-
tom frequency and display offsets.
