Page 129
FT
DX
5000 O
PERATING
M
ANUAL
MODE-RTY G
ROUP
089 RTTY LCUT FRQ
Function
: Selects the cutoff frequency of the lower side
of the RX audio filter in the RTTY mode.
Available Values
: OFF / 100Hz ~ 1000Hz (50 Hz/step)
Default Setting
: 300Hz
090 RTTY LCUT SLP
Function
: Selects the filter slope of the lower side of the
RX audio filter in the RTTY mode.
Available Values
: 6dB/oct or 18dB/oct
Default Setting
: 18dB/oct
091 RTTY HCUT FRQ
Function
: Selects the cutoff frequency of the upper side
of the RX audio filter in the RTTY mode.
Available Values
: OFF / 700Hz ~ 4000Hz (50 Hz/step)
Default Setting
: 3000Hz
092 RTTY HCUT SLP
Function
: Selects the filter slope of the upper side of the
RX audio filter in the RTTY mode.
Available Values
: 6dB/oct or 18dB/oct
Default Setting
: 18dB/oct
093 RTTY R PLRTY
Function
: Selects normal or reverse Mark/Space polarity
for RTTY receive operation.
Available Values
: NOR / REV
Default Setting
: NOR
094 RTTY T PLRTY
Function
: Selects normal or reverse Mark/Space polarity
for RTTY transmit operation.
Available Values
: NOR / REV
Default Setting
: NOR
095 RTTY RTTY OUT
Function
: Selects the receiver to be connected to the data
output port (pin 2) of the
RTTY
jack.
Available Values
: VFO-A / VFO-B
Default Setting
: VFO-A
096 RTTY OUT LVL
Function
: Sets the FSK RTTY data output level at the
output port (pin 2) of the
RTTY
jack.
Available Values
: 0 ~ 100
Default Setting
: 50
097 RTTY SHIFT
Function
: Selects the frequency shift for FSK RTTY op-
eration.
Available Values
:170Hz / 200Hz / 425Hz / 850Hz
Default Setting
: 170Hz
098 RTTY TONE
Function
: Selects the Mark tone for RTTY operation.
Available Values
: 1275Hz / 2125Hz
Default Setting
: 2125Hz
M
ENU
M
ODE
MODE-SSB G
ROUP
099 A3J LCUT FRQ
Function
: Selects the cutoff frequency of the lower side
of the RX audio filter in the SSB mode.
Available Values
: OFF / 100Hz ~ 1000Hz (50 Hz/step)
Default Setting
: 100Hz
100 A3J LCUT SLP
Function
: Selects the filter slope of the lower side of the
RX audio filter in the SSB mode.
Available Values
: 6dB/oct or 18dB/oct
Default Setting
: 6dB/oct
101 A3J HCUT FRQ
Function
: Selects the cutoff frequency of the upper side
of the RX audio filter in the SSB mode.
Available Values
: OFF / 700Hz ~ 4000Hz (50 Hz/step)
Default Setting
: 3000Hz
102 A3J HCUT SLP
Function
: Selects the filter slope of the upper side of the
RX audio filter in the SSB mode.
Available Values
: 6dB/oct or 18dB/oct
Default Setting
: 6dB/oct
103 A3J MIC SEL
Function
: Selects the microphone to be used on the SSB
modes (LSB and USB).
Available Values
: FRONT / DATA / PC
Default Setting
: Frnt
FRONT: Selects the microphone connected to the front
panel
MIC
jack while using the SSB modes.
DATA: Selects the microphone connected to pin 1 of
the
PACKET
Jack while using the SSB
modes.
PC:
This parameter is for future expansion of this
transceiver’s capabilities, but at this time is
not supported.
104 A3J TX BPF
Function
: Selects the audio passband of the DSP modula-
tor on the SSB mode.
Available Values
: 50-3000 / 100-2900 / 200-2800 /
300-2700 / 400-2600 / 3000WB
Default Setting
: 300-2700 (Hz)
N
OTE
:
The apparent power output, when using the widest band-
widths, may seem lower. This is normal, and it occurs be-
cause the available transmitter power is distributed over a
wider bandwidth. The greatest compression of power out-
put, conversely, occurs when using the “400-2600” set-
ting (400-2600 Hz), and this setting is highly recommended
for contest or DX pile-up work.
Summary of Contents for FTDX5000 CAT BOOK
