Page 127
FT
DX
5000 O
PERATING
M
ANUAL
063 A1A BK-IN
Function
: Sets the CW “break-in” mode.
Available Values
: SEMI / FULL
Default Setting
: SEMI
SEMI: The transceiver will operate in the semi break-
in mode. The delay (receiver recovery) time is
set by the front panel [
DELAY
] knob.
FULL: The transceiver will operate in the full break-
in (QSK) mode.
064 A1A SHAPE
Function
: Selects the CW carrier wave-form shape (rise/
fall times).
Available Values
: 1ms / 2ms / 4ms / 6ms
Default Setting
: 4 ms
065 A1A WEIGHT
Function
: Sets the Dot:Dash ratio for the built-in elec-
tronic keyer.
Available Values
: (1:) 2.5 ~ 4.5
Default Setting
: 3.0
066 A1A FRQ DISP
Function
: Selects the frequency Display Format for the
CW mode.
Available Values
: FREQ / PITCH
Default Setting
: PITCH
FREQ: Displays the receiver carrier frequency, with-
out any offset added. When changing modes
between SSB and CW, the frequency display
remains constant.
PITCH: This frequency display reflects the added
BFO offset.
067 A1A PC KYNG
Function
: Enables/disables CW keying from the
“PACKET PTT” terminal (pin 3) on the rear panel’s
PACKET
jack while operating in the CW mode.
Available Values
: DISABLE / ENABLE
Default Setting
: DISABLE
068 A1A QSK TIME
Function
: Selects the time delay between when the
PTT
is keyed and the carrier is transmitted during QSK opera-
tion when using the internal keyer.
Available Values
: 15ms / 20ms / 25ms / 30 ms
Default Setting
: 15ms
MODE-DAT G
ROUP
069 DATA DATA IN
Function
: Selects the data input path to be used in the
PKT mode.
Available Values
: DATA / PC
Default Setting
: DATA
DATA: Uses the data input line connected to pin 1 of
the
PACKET
jack while using the PKT mode.
PC:
This parameter is for future expansion of this
transceiver’s capabilities, but at this time is
not supported.
070 DATA DT GAIN
Function
: Sets the data input level from the TNC to the
AFSK modulator.
Available Values
: 0 ~ 100
Default Setting
: 50
071 DATA DT OUT
Function
: Selects the receiver to be connected to the data
output port (pin 4) of the
PACKET
jack.
Available Values
: VFO-A / VFO-B
Default Setting
: VFO-A
072 DATA OUT LVL
Function
: Sets the AFSK data output level at the output
port (pin 4) of the
PACKET
jack.
Available Values
: 0 ~ 100
Default Setting
: 50
073 DATA VOX DLY
Function
: Adjusts the “VOX” delay (receiver recovery)
time in the PKT mode.
Available Values
: 30ms ~ 3000ms (10 ms/step)
Default Setting
: 300ms
074 DATA VOX GAIN
Function
: Adjusts the “VOX” gain in the PKT mode.
Available Values
: 0 ~ 100
Default Setting
: 50
MODE-CW G
ROUP
M
ENU
M
ODE
Summary of Contents for FTDX5000 CAT BOOK
