70
FT-2900R O
PERATING
M
ANUAL
“S
ET
”
(
M
ENU
)
M
ODE
M
ENU
I
TEM
1 APO
2 AR BEP
3 AR INT
4 ARS
5 BCLO
6 BEEP
7 BELL
8 BNK.LNK
9 BNK NM
10 CLK.SFT
11 CW ID
12 CWTRNG
13 DC VLT
14 DCS CD
15 DCS RV
16 DIMMER
17 DT A/M
18 DT DLY
19 DT SET
20 DT SPD
21 EDG.BEP
22 INT CD
23 INT MD
24 INT.A/M
25 INT.SET
26 LOCK
27 MCGAIN
28 MEM.SCN
A
VAILABLE
V
ALUES
30MIN / 1HOUR / 3HOUR /
5HOUR / 8HOUR / OFF
IN RNG / ALWAYS / OFF
25SEC / 15SEC
ON / OFF
ON / OFF
KY+SCN / KEY / OFF
1 / 3 / 5 / 8 / CNTNUE / OFF
---
---
ON / OFF
ON / OFF
4WPM - 13WPM / 15WPM /
17WPM / 20WPM / 24WPM /
30WPM / 40WPM / OFF
(20CPM - 65CPM (5CPM multiples)
/ 75CPM / 85CPM / 100CPM /
120CPM / 150CPM / 200CPM)
---
104 standard DCS codes
ENABLE / DISABL
LVL 0 (OFF) - LVL 10
MANUAL / AUTO
50 / 250 / 450 / 750 / 1000 (ms)
---
50 / 100 (ms)
ON / OFF
DTMF 0 - DTMF 9 /
DTMF A -DTMF F
SRG / FRG
MANUAL / AUTO
---
KEY / DIAL / K+D / PTT /
K+P / D+P / ALL
LVL 1 -LVL 9
TAG1 / TAG2 / ALL CH
F
UNCTION
Enables/Disables the Automatic Power Off feature.
Selects the Beep option during ARTS™ operation.
Selects the Polling Interval during ARTS™ operation.
Activates/Deactivates the Automatic Repeater Shift feature.
Enables/Disables the Busy Channel Lock-Out feature.
Enables/Disables the key beeper.
Selects the CTCSS/DCS/EPCS Bell Ringer repetitions.
Select the Memory Bank for the Memory Bank Link Scan.
Programming an Alpha/Numeric label for a Memory Bank.
Shifting of the CPU clock frequency.
Enables/Disables the CW identifier during ARTS™ Operation.
Enables/Disables the CW Training feature and selects the sending
speed of the morse Code.
Indicates the DC Supply Voltage.
Setting of the DCS code.
Enables/Disables “Inverted” DCS code decoding.
Setting of the front panel display’s illumination level.
Enables/Disables the DTMF Autodialer feature.
Setting of the DTMF Autodialer’s TX Delay Time.
Loading of the DTMF Autodialer Memories.
Setting of the DTMF Autodialer Sending Speed.
Enables/Disable the Band-edge beeper while scanning.
Selects the Access Number (DTMF digit) for WiRES™ operation.
Selects the Internet Link Connection mode.
Enables/Disables DTMF Autodialer feature while operating on the
Internet Connection feature.
Selects the memory register for an Access Number (DTMF code) for
non-WiRES™ Internet Link System access.
Selects the Control Locking Lockout combination.
Adjust the microphone gain level.
Selects the Memory Scan mode.
D
EFAULT
OFF
IN RNG
25SEC
ON
OFF
KY+SCN
OFF
---
---
OFF
OFF
OFF
---
023
DISABL
LVL 5
MANUAL
450 (ms)
---
50 (ms)
OFF
DTMF 1
SRG
MANUAL
---
K+D
LVL 5
ALL CH
The
FT-2900R
Set (Menu) mode, already described in parts of many previous chapters, is
easy to activate and set. It may be used for configuration of a wide variety of transceiver
parameters, some of which have not been detailed previously. Use the following procedure
to activate the Set (Menu) mode:
1. Press and hold in the [
MHz
(
SET
)] key for one second to enter the Set mode.
2. Rotate the
DIAL
knob to select the Menu Item to be adjusted.
3. Press the [
MHz
(
SET
)] key momentarily to enable adjustment of the selected Menu
item, then rotate the
DIAL
knob to perform the actual adjustment.
4. After completing your selection and adjustment, press and hold in the [
MHz
(
SET
)] key
for one second to exit the Set mode and resume normal operation.
