manualshive.com logo in svg

Xylem Lowara e-IXPSA, Additional Installation, Operation And Maintenance Instructions

Share
Download
Xylem Lowara e-IXPSA Additional Installation, Operation And Maintenance Instructions Download Page 2

en – Original instructions 

 

 

2 

e-IXPSA – Additional Installation, Operation and Maintenance Manual

 

 

Table of Contents 

 

1

 

Introduction and Safety

 ............................................................................................................................................ 5

 

1.1

 

Introduction

 ...................................................................................................................................................... 5

 

1.2

 

Hazard levels and safety symbols

 .................................................................................................................... 5

 

1.3

 

User safety

 ........................................................................................................................................................ 6

 

1.4

 

Explosion protection

 ........................................................................................................................................ 6

 

1.4.1

 

Explosion protection marking

 ..................................................................................................................... 7

 

1.4.1

 

Temperature limits

 ....................................................................................................................................... 7

 

1.4.2

 

Operation of the pump

 ................................................................................................................................ 8

 

1.4.3

 

Electric switches and control devices, instrumentation and accessories

 ................................................... 9

 

1.4.4

 

Intended use

 ................................................................................................................................................. 9

 

1.5

 

Protection of the environment

 ....................................................................................................................... 10

 

1.6

 

Spare parts

...................................................................................................................................................... 10

 

2

 

Handling and Storage

 ............................................................................................................................................. 11

 

2.1

 

Unit inspection upon delivery

 ........................................................................................................................ 11

 

2.1.1

 

Package inspection

 .................................................................................................................................... 11

 

2.1.2

 

Unpacking and inspection of the unit

 ....................................................................................................... 11

 

2.2

 

Guidelines for transport

 ................................................................................................................................. 11

 

2.2.1

 

Handling of the packed unit using a forklift truck

 ..................................................................................... 12

 

2.2.2

 

Lifting with a crane

 ..................................................................................................................................... 12

 

2.3

 

Storage

 ........................................................................................................................................................... 13

 

2.3.1

 

Storage of the packed unit

 ........................................................................................................................ 13

 

2.3.2

 

Long-term storage of the unit

 .................................................................................................................... 14

 

2.3.3

 

Return

.......................................................................................................................................................... 14

 

3

 

Description of the product

 ..................................................................................................................................... 15

 

3.1

 

Features

 .......................................................................................................................................................... 15

 

3.2

 

Data plate

 ....................................................................................................................................................... 16

 

3.3

 

Identification code

 ......................................................................................................................................... 16

 

3.4

 

ATEX label

 ...................................................................................................................................................... 17

 

3.5

 

Part names

 ...................................................................................................................................................... 18

 

4

 

Installation

 ............................................................................................................................................................... 19

 

4.1

 

General precautions

 ....................................................................................................................................... 19

 

4.2

 

Mechanical installation

 ................................................................................................................................... 19

 

4.2.1

 

Precautions

 ................................................................................................................................................. 19

 

4.2.2

 

Installation area

 .......................................................................................................................................... 19

 

4.2.3

 

Installation on concrete foundation

 ........................................................................................................... 20

 

4.3

 

Hydraulic connection

 ..................................................................................................................................... 21

 

4.3.1

 

Precautions

 ................................................................................................................................................. 21

 

Summary of Contents for Lowara e-IXPSA

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands