manualshive.com logo in svg

Xylem Lowara e-IXPSA, Additional Installation, Operation And Maintenance Instructions

Share
Download
Xylem Lowara e-IXPSA Additional Installation, Operation And Maintenance Instructions Download Page 13

en – Original instructions 

 

 

e-IXPSA – Additional Installation, Operation and Maintenance Manual  

13

 

 

Preparing the unit for lifting 

The figure shows how to harness the unit with or without motor. 

 

1.

 

Use the ropes to make a tie harness. 

2.

 

Fix the ropes to the crane. 

3.

 

Lift the crane and tension the ropes without lifting the unit. 

Lifting and positioning

 

1.

 

Lift and move the unit slowly 

2.

 

Set the unit down slowly. 

3.

 

Release the harness. 

2.3

 

Storage 

Precautions 

 

WARNING: risk of injury 

Pay attention to liquids that are excessively hot or cold. 

 

 

WARNING: 

Make sure that the drained liquid cannot cause damage or injuries. 

 

 

WARNING: 

It is prohibited to dispose of lubricant liquids and other hazardous substances in the 

environment. 

2.3.1

 

Storage of the packed unit 

The unit must be stored:

 

•

 

In a covered and dry place 

•

 

Away from heat sources 

•

 

Protected from dirt 

Summary of Contents for Lowara e-IXPSA

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands