background image

6 142027(G) 

Electrical Noise 

Electrical noise is seldom responsible for damaging components, unless extremely high 
energy or high voltage levels are present. However, noise can cause temporary 
malfunctions that can result in hazardous machine operation in certain applications. Noise 
may be present only at certain times, may appear at widely spread intervals, or in some 
cases may exist continuously. 
 
Noise commonly enters through input, output, and power supply lines and may also be 
coupled through the capacitance between these lines and the noise signal carrier lines. 
This usually results from the presence of high voltage or long, close-spaced conductors. 
When control lines are closely spaced with lines carrying large currents, the coupling of 
magnetic fields can also occur. Use shielded cables to help minimize noise. Potential 
noise generators include switching components, relays, solenoids, motors, and motor 
starters. 
 
Refer to the relevant Federal, State/Provincial, and local electric codes, which provide 
data such as the size and types of conductors, color codes and connections necessary for 
safe grounding of electrical components. It is recommended that high- and low-voltage 
cabling be separated and dressed apart. In particular, AC cables and switch wiring should 
not be in the same conduit with all communication cables. 
 

Line Voltage Variation 

The power supply section of the unit is built to sustain the specified line fluctuations and 
still allow the system to function in its operating margin. As long as the incoming voltage 
is adequate, the power supply provides all the logic voltages necessary to support the 
monitor unit. 
 
Unusual AC line variations may cause undesirable system shutdowns. As a first step to 
reduce line variations, correct any possible feed problems in the distribution system. If 
this correction does not solve the problem, use a constant voltage transformer. The 
constant voltage transformer stabilizes the input voltage to the systems by compensating 
for voltage changes at the primary in order to maintain a steady voltage at the secondary. 
When using a constant voltage transformer, check that the power rating is sufficient to 
supply the unit. 

 

Location and Enclosure 

 

Place the unit to allow easy access to the system ports. 

 

Account for the unit dimensions when selecting an installation location or enclosure (see pg. 3). 

 

You can maintain the NEMA 4 seal by mounting the unit in an approved enclosure 
that has a 14 gauge (0.075"/1.9 mm thick) steel or (0.125"/3.2 mm thick) aluminum 
front face. 

 

Place the unit at a comfortable working level. 

 

Mount the unit in an upright position, if possible. 

 

Consider locations of accessories such as AC power outlets and lighting (interior 
lighting and windows) for installation and maintenance convenience. 

 

Prevent condensation by installing a thermostat-controlled heater or air conditioner. 

 

Avoid obstructing the airflow to allow for maximum cooling. 

 

Place any fans or blowers close to the heat-generating devices. If using a fan, make 
sure that outside air is not brought inside the enclosure unless a fabric or other

 

 

reliable filter is used. This filtration prevents conductive particles or other harmful 

Summary of Contents for XT1502




















Reviews: