Xtreme Manufacturing XR5919-A, Operation And Safety Manual

Page: 25 / 78

Chapter 4 – Controls
XR5919-A 19
Figure 4.14 – Display Indicators
A. Turn Signal
The corresponding left or right arrow blinks when the
turn signal switch is operated. Both arrows blink when
the hazard switch is enabled.
B. Steering Axle Position
The Axle Position Indicator illuminates and displays “Axle
Center” when the rear wheels are aligned perpendicular to
the rear axle. The rear wheels should be centered before
changing steering modes.
The Axle Position Indicator illuminates and displays “Axle
Lock” when the Telehandler is in the axle lock mode.
The rear axle locks when the parking brake is set to ON
(engaged), or the transmission is in NEUTRAL or the
service brake is applied, and when the boom is above 10°.
If the “Axle Lock” Indicator does not illuminate when the
Telehandler is in the axle lock mode, stop the Telehandler,
follow proper shut down procedures, tag Telehandler with
“Do Not Operate” tags, and have a qualified mechanic
service or repair the Telehandler BEFORE placing it into
service again.
C. High Hydraulic Oil Temperature
The hydraulic oil temperature indicator illuminates when
the oil temperature is above 1800 F. If the hydraulic oil
temperature indicator illuminates, stop and idle the engine
to allow time for cooling. If the hydraulic oil temperature
indicator does not go out after five (5) minutes, stop
the forklift, follow proper shut down procedures, tag the
forklift with “Do Not Operate” tags, and have a qualified
mechanic service or repair the forklift BEFORE placing
it into service again.
D. Water In Fuel
The Water in Fuel Indicator will be displayed when water
is detected in the fuel filter. Drain the water by opening
the petcock on the bottom of the fuel filter.
If there is no alert, the top row indicators disappear.
E. Parking Brake
The Parking Brake Indicator will be displayed when the
parking brake is applied.
A
B C D E F G H I
J
L
N R S
K
M
O P
Q
F. Oil Pressure
The Oil Pressure Indicator will be displayed when the
engine oil pressure is below normal. If the Oil Pressure
Indicator comes on during normal operation, stop the
forklift, follow proper shut down procedures, tag forklift
with “Do Not Operate” tags, and have a qualified me-
chanic service or repair the forklift BEFORE placing it
into service again.
Note
The indicator at position G has more than one function
as described below. Refer to the Operation section on
Warning Indicators.
G. Wait to Start
The Wait to Start Indicator is displayed when the key
switch is moved to the RUN position. Wait until the indi-
cator goes out before starting the engine.
G. General Warning
After the engine is started, the Wait To Start Indicator
goes out. It is replaced by a Warning Indicator which is
displayed when there’s a general warning. When the
Warning Indicator comes on, a description of the warning
is displayed on the Message Display at position N (instead
of the digital clock showing).
G. Engine Stop
The Engine Stop Indicator is displayed when the engine
is shut down. It is displayed with a flashing Check Engine
Indicator when an engine shutdown is imminent. The
Engine Stop Indicator will be displayed when there is a
serious engine fault and the engine should be shut down.
H. Engine Service Required
The Engine Service Required Indicator will be displayed
when a maintenance interval has been exceeded.
I. Back-Up Camera
Optional equipment.
J. Engine Load
Displays the percent of rated load for the current engine
RPM that is being applied to the engine.
K. Fuel Gauge
Indicates the approximate quantity of fuel in the tank. The
total capacity of the fuel tank is 17 gallons.
L. Engine Temperature Gauge
Indicates the temperature of the coolant in the engine
cooling system. After starting the forklift, allow time for the
Engine Temp Gauge to begin moving before operating the
forklift. After the engine has sufficiently been warmed up,
normal engine coolant temperature should read between
180° to 200° F.
M. Voltage Gauge
Indicates the amount of charge (in Volts). Normal system
voltage is between 12.5 and 14 Volts. If the voltage gauge
shows abnormal readings, stop the forklift, follow proper
shut down procedures, tag forklift with “Do Not Operate”