background image

Chapter 4 – Controls

16 XR5919-A

Operator Seat

Seat Controls

The operator seat can be adjusted two (2) ways: fore and 

aft, and backrest angle. 

Figure 4.4 – Seat Controls

Backrest Angle Adjustment Lever

Pull the backrest angle adjustment lever up to release the 

seat backrest lock. Adjust the angle of the backrest and 

release the lever to lock the backrest to the desired angle.

Fore and Aft Adjustment Lever

Pull the fore and aft adjustment lever outward from the 

seat to release the seat lock. Slide the seat forward or 

backward to a comfortable location and release the lever 

to lock the seat in the desired position.

Seat Belt

Warning

Always check the condition of the seat belt and 

mounting hardware before operating the Telehandler. 

If the seat belt or mounting hardware is defective, it 

may not properly restrain the operator, which could 

result in death or serious injury.

•  DO NOT operate the Telehandler until the seat belt or 

mounting hardware is replaced, if worn or damaged.

•  The seat belt MUST be worn while operating the 

Telehandler. Failure to wear the seat belt could result 

in death or serious injury.

The Telehandler is equipped with a standard two inch 

(2”) wide retractable seat belt. A three inch (3”) wide 

retractable seat belt is available where required by state 

and local laws and regulations.

Warning

DO NOT adjust the seat or seat belt while the Tele-

handler is moving.  Keep both hands on the wheel 

while the Telehandler is moving to prevent loss of 

Telehandler control which could result in death or 

serious injury.

Before starting the engine, adjust the seat for position and 

comfort (refer to the Operator Seat section of this manual) 

and then adjust the seat belt as follows:

  1. Grasp the free end of the seat belt (located on the 

right side of the seat) and make sure the belt webbing 

is not twisted or entangled in any portion of the seat 

assembly.

  2.  Pull the retractable seat belt across your lap. Position 

the seat belt as low on your body as possible.

  3.  Insert the latch plate into the buckle (on the right side 

of the seat) until a “click” is heard.

  4.  Make sure seat belt retracts snugly across your lap.

Fire Extinguisher

A fire extinguisher is mounted in the operator cab.

Figure 4.5 – Fire Extinguisher

Rear View Mirrors

Two adjustable rear view mirrors are provided to aid the 

operator’s rear vision. The rear-view mirrors are mounted 

on the upper left of the operator’s cab and the right front 

of the chassis.

Backrest Angle 

Adjustment Lever

Fore and Aft

 Adjustment Lever

Retractable Seat Belt

Seat Belt Buckle 

and Release Button

Summary of Contents for XR5919-A















































































Reviews: