background image

5

ERG400 Rower

•  To disconnect, turn all controls to the off position, then remove the plug from the outlet.

•  Do not operate equipment on deeply padded, plush or shag carpet. Damage to both carpet and  

equipment may result.

•  Before beginning this or any exercise program, consult a physician. This is especially important for  

persons over the age of 35 or persons with pre-existing health conditions.

•  Keep hands away from all moving parts.

•  The pulse sensors are not medical devices. Various factors, including the user’s movement, may affect the 

accuracy of heart rate readings. The pulse sensors are intended only as exercise aids in determining heart 

rate trends in general.

•  Do not attempt to use your equipment for any purpose other than for the purpose it is intended.

•  Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on your  

equipment. Quality athletic shoes are recommended to avoid leg fatigue.

Important Safety Instructions

When using an electrical appliance, basic precautions should always be followed, including the following:
Read all instructions before using this appliance.

DANGER

 - To reduce the risk of electric shock:

1.  Always unplug this appliance from the electrical outlet immediately after using and before cleaning.

WARNING

 - To reduce the risk of burns, fire electric shock, or injury to persons: 

1.  An appliance should never be left unattended when plugged in. Unplug from outlet when not in use, and 

before putting on or taking off parts. 

2.  Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury 

to persons.

3.  Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled 

persons.

4.  Use this appliance only for its intended use as described in this manual. Do not use attachments not  

recommended by the manufacturer.

5.  Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been 

dropped or damaged, or dropped into water. Return the appliance to a service center for examination and 

repair. 

6.  Do not carry this appliance by supply cord or use cord as a handle. 
7.  Keep the cord away from heated surfaces.
8.  Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the 

like.

9.  Never drop or insert any object into any opening. 
10. Do not use outdoors.
11.  Do not operate where aerosol (spray) products are being use or where oxygen is being administered. 
12. Connect this appliance to a properly grounded outlet only.
13. The appliance is intended for household use. 

SAVE THESE INSTRUCTIONS - THINK SAFETY!

Fitness Equipment Safety Instructions

CAUTION!! Please be careful when unpacking the carton.

Failure to follow all guidelines may compromise the effectiveness of the exercise experience, expose  

yourself (and possibly others) to injury, and reduce the longevity of the equipment.

Summary of Contents for ERG400

















Reviews: