15
S y s t e m
7. Proximity Card Access Security Programming
This part explains how to configure the Proximity card access function, by means of keypad. Please note, to a
Door Station without access security, all the related parameters can’t be updated.
It is much convenient to manage access security and cards by means of IDS software in a networked system. The
standard capacity is 500 cards, and can be upgraded to 5,000 cards if needed. Reading distance is
approximately 30mm from the window.
7.1.
Access Security Programming Overview
There are 2 type of setup, for Access controller and cards authorization, located in Program Menu 6,7.
Door Station should enter Debug State first, and then operate as below.
[ 6 ] A c c e s s S e c u r i t y
- - - - - - - - - - - - - - - - - - - - - - - - - - -
- 1 . A c c e s s F u n c t i o n [ 1 ]
- 2 . P a s s i v e A d d r e s s [ 1 ]
- 3 . A C S A d d r e s s [ 1 2 1 ]
> > D E B U G S T A T E < <
- - - - - - - - - - - - - - - - - - - - - - - - - - -
# - # P r o g r a m G u i d e
0 - # R e d i a l L a s t N b r s
1 - # D o w n l o a d f r o m P C
2 - # D e b u g T o o l s
- - - - - - - - - O p t i o n s - - - - - - - - - -
< > V o l u m e A d j u s t
< > A u t o D i a l B a c k
< > D i s p l a y N e t D a t a
<
●
> D i s p l a y A l a r m
< > G u a r d U n i t O n l i n e
- - - - - - - - - - - - - - - - - - - - - - - - - - -
D a t a 1 . . .
D a t a 2 . . .
V i d e o E n t r y
> > P r o g r a m G u i d e < <
- - - - - - - - - - - - - - - - - - - - - - - - - - -
[ 1 ] C o n f i g u r a t i o n
[ 2 ] U n l o c k S e t t i n g
[ 3 ] M o n i t o r P r o g r a m
[ 4 ] I n f o r m a t i o n
[ 5 ] O p e r a t i n g O p t i o n s
[ 6 ] A c c e s s S e c u r i t y
[ 7 ] C a r d M a n a g e m e n t
[ 8 ] S y s t e m M a i n t a i n
[ 9 ] A d v a n c e d C o n f i g
- - - - - - - - - - - - - - - - - - - - - - - - - - -
P r e s s 1 ~ 9 t o s e l e c t
* B a c k
V i d e o E n t r y S y s t e m
- 4 . C l o c k . . .
- 5 . U n l o c k V e r i f y [ 0 ]
- - - - - - - - - - - - - - - - - - - - - - - - - - -
P r e s s 1 ~ 5 t o s e l e c t
* B a c k
V i d e o E n t r y S y s t e m
[ 7 ] C a r d M a n a g e m e n t
= = = = = = = = = = = = = = = = = = = =
- 1 . A d d C a r d
- 2 . D e l e t e b y C a r d
- 3 . D e l e t e b y M . C o d e
- 4 . C a r d s I n f o r m a t i o n
- 5 . M a s t e r C a r d
Press “#” twice
Press number
6 or 7
, to
enter setup menu
- - - - - - - - - - - - - - - - - - - - - - - - - - -
P r e s s 1 ~ 5 t o s e l e c t
* B a c k
V i d e o E n t r y S y s t e m
-
About access security controller
The
Access Security
parameter must be set to 1, so as to activate the access controller.
As the built-in access controller works independently, the controller addresses is necessary and must be
unique in one system, which is
ACS address
. Normally, the
ACS address
is associated with Door Station
Netware Address automatically, and you don’t need to setup it.
-
About cards
One card can only be authorized one time; repeated card will not be recognized and registered.
Three types of cards are supported: User Card, Master Card and Manage Card.
1)
User Cards
are associated with Room Code; an authorized User Card can open the door at any time.
2)
Master Card
will serve direct access to enter Debug Mode, and only one card can be assigned.
3)
Manage Card
is restricted to pre-defined access rule, and hold by visitor or service person.
Please note, Manage Cards can only be authorized by means of IDS-800 software.
