XT Racing GPX Pro User Manual Download Page 76 | Manualshive

Page: 76 / 95

background image

GPX Pro Manual

72

© 2009 XT Racing

input. If you have acceleration turned on and calibrated, then the acceleration data will appear as
two entries in the list.

·

Accel lat

- the latitudinal acceleration, which is the acceleration to the right or left of the

direction you were traveling; in other words, this is the turning acceleration

·

Accel long

- the longitudinal acceleration, which is the acceleration in the direction you were

traveling; in other words, this is the braking or throttle acceleration

2.4.3.2

Gear overlay

If you have a data channel calibrated as a gear input or are using the RPM gear ratio calculator
then this option will make visible the overlayed gear display.  The display of gear is not limited to
taking up the whole graph area.  It is an overlay that you can turn on while looking at another
input, for example RPM.  This allows you to analyze your RPM and your gear changes at the same
time.

«
...
74
75
76
77
78
...
»

Summary of Contents for GPX Pro
































































































Reviews:

No comments

Related manuals for GPX Pro

Brand: Trumeter Pages: 2

Brand: AirCycler Pages: 7

Brand: Allegion Pages: 4

Brand: Rachio Pages: 11

Brand: Beckmann Pages: 38

Brand: Uniblitz Pages: 43

Brand: Caen Pages: 10

Brand: Malmbergs Pages: 8

Brand: Philips Pages: 2

Brand: BAREBO Pages: 2

Brand: Velleman Pages: 4

Busch-Timer 6455

Brand: Busch-Jaeger Pages: 33

Brand: Pact Pages: 3

4 Way Timer & Clock

Brand: Salter Pages: 2

Brand: Masterplug Pages: 2

Brand: Finglai Pages: 2

Brand: Flo Fab Pages: 4

Brand: Conrad Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands