Xsens MTi 10 Series User Manual Download | Manualshive

Page: 52 / 84

background image

Document MT0605P.E

© Xsens Technologies B.V.

MTi User Manual

48

4.13 Status byte

The status byte includes information about the status of the MTi, its sensors, the filter and user inputs.
The following information can be found in the status byte and status word:

Status byte (DataID 0xE010) is the short status byte (8 bits), identical to the status byte of the legacy
output message (see section 4.10).
Status word (DataID 0xE020) is an extended 32 bits status message. The bits in StatusWord are
defined in the following table (note that bit 0:7 are the same as Status Byte):

Bits

Field

Description

0

Selftest

This flag indicates if the MT passed the latest self-test
(

RunSelftest

).

1

Filter Valid

This flag indicates if input into the filter orientation filter is
reliable and / or complete. If for example the measurement
range of internal sensors is exceeded, orientation output cannot
be reliably estimated and the filter flag will drop to 0. For the
MTi-G, the filter flag will also become invalid if the GPS status
remains invalid for an extended period

2

GPS fix

This flag indicates if the GPS unit has a proper fix. The flag is
only available in MTi-G units.

3:4

NoRotationUpdate Status

(only available for legacy devices):
This flag indicates the status of the no rotation update
procedure in the filter after the SetNoRotation message has
been sent.

11: Running with no rotation assumption
10: Error: Rotation detected, procedure not started

(sticky)

01: Estimation complete, some samples rejected

(sticky)

00: Estimation complete, no errors

5

Timestamp GPS synced

6

Timestamp clock synced

7

On/Off

8

Clipflag Acc X

If set an out of range acceleration on the X axis is detected

9

Clipflag Acc Y

If set an out of range acceleration on the Y axis is detected

10

Clipflag Acc Z

If set an out of range acceleration on the Z axis is detected

11

Clipflag Gyr X

If set an out of range angular velocity on the X axis is detected

12

Clipflag Gyr Y

If set an out of range angular velocity on the Y axis is detected

13

Clipflag Gyr Z

If set an out of range angular velocity on the Z axis is detected

14

Clipflag Mag X

If set an out of range magnetic field on the X axis is detected

15

Clipflag Mag Y

If set an out of range magnetic field on the Y axis is detected

16

Clipflag Mag Z

If set an out of range magnetic field on the Z axis is detected

17:18 NoVelocityUpdate status

«
...
50
51
52
53
54
...
»

Summary of Contents for MTi 10 Series





















































































Reviews:

No comments

Related manuals for MTi 10 Series

Brand: X-Rite Pages: 50

Brand: YOSensi Pages: 26

Brand: YOSensi Pages: 26

Brand: Polimaster Pages: 6

Brand: STONEX Pages: 99

iTrans 77023554

Brand: Industrial Scientific Pages: 94

Proline Promag 50H

Brand: Endress+Hauser Pages: 52

SS9007.3 Mini CT Meter

Brand: Saturn South Pages: 18

Brand: Badger Meter Pages: 32

Brand: Frama Pages: 2

Brand: Leviton Pages: 2

Proline Promass 200

Brand: Endress+Hauser Pages: 12

wtw Cleaning Air Box -115 VAC

Brand: Xylem Pages: 32

Brand: Xylem Pages: 44

Brand: BRUEL & KJAER Pages: 26

Brand: Efergy Pages: 2

Visio R-400VDN Series

Brand: Pentax Pages: 56

iTrixx-Ultra 300

Brand: Linortek Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands