Xray XB808 Instruction Manual Download Page 16

Page: 16 / 40

KICK-UP

ROLL CENTER

909395

SS 3.5x45

909372

SS 3.5x22

5. FRONT SUSPENSION

33 3450

ANTI-ROLL BAR BALL JOINT 5.8 MM (2)

35 2002

XB808 DIFF BULKHEAD BLOCK SET FRONT/REAR

35 2114

XB808 COMPOSITE FRONT LOWER SUSPENSION ARM

35 2302

XB808 COMPOSITE FRONT LOWER SUSP. HOLDERS SET

35 2317

XB808 STEEL SUSP. HOLDER - FRONT - LASER CUT

35 2460

PIVOT BALL 5.8 (10)

35 2470

BALL JOINT 5.8 (8)

35 2484

XB808 FRONT ANTI-ROLL BAR 2.4MM

35 3371

XB808 SET OF COMPOSITE LOWER ARM SHIMS

35 7213

XB808 LOWER INNER PIVOT PIN SCREW 4MM (2)

90 1303

HEX SCREW SB M3x3 (10)

90 1305

HEX SCREW SB M3x5 (10)

90 1312

HEX SCREW SB M3x12 (10)

90 1408

HEX SCREW SB M4x8 (10)

90 2318

HEX SCREW SH M3x18 (10)

90 3308

HEX SCREW SFH M3x8 (10))

90 9372

SCREW PHILLIPS SS 3.5x22 (10)

90 9395

SCREW PHILLIPS SS 3.5x45 (10)

96 0040

NUT M4 (10)

BAG

909372

960040

902318

352114

903308

353371

901408

901303

333450

352470

901312

352460

901305

352002

352484

352302

357213

909395

352302

3.5x22

3.5x45

FRONT VIEW

The composite suspension holders feature

preset optimum geometry 0° kick-up which

with the combination of the 10° angled

chassis creates total 10° kick-up. Use optional

adjustable suspension holders for further

geometry adjustment.

352317

FRONT ANTI-ROLL BARS

#352480

2.0mm (OPTION)

#352482

2.2mm (OPTION)

#352484

2.4mm (STANDARD)

#352486

2.6mm (OPTION)

#352488

2.8mm (OPTION)

REAR VIEW

Do not overtighten the screws.
Overtightening may result in
composite suspension holder
deformation.

Summary of Contents for XB808









































Search results

Summary of Contents for XB808

Reviews:

Related manuals for XB808

Brands by name

Popular brands

Xray XB808, Instruction Manual

Search results

Summary of Contents for XB808

Reviews:

Related manuals for XB808

Brands by name

Popular brands