Xray XB808 Instruction Manual Download Page 27 | Manualshive

Page: 27 / 40

background image

27

GEARING

CLUTCH

902316

SH M3x16

911410

SHF M4x10

908308

SCH M3x8

908312

SCH M3x12

359051

BB 5x12x4

961025

S 2.5

962050

S 5x10x1

901405

SB M4x5

902308

SH M3x8

903410

SFH M4x10

960030

N M3

964073

S 7x10x0.2

964074

S 7x10x0.3

964075

S 7x10x0.5

903310

SFH M3x10

7x10x0.2 / 0.3 / 0.5

3x8

5x10

2.5

Adjust engine position to achieve
proper gear mesh

Use appropriate shims to achieve
proper clutchbell endplay

Note the orientation of the
clutch shoes. The short side of
spring must be in the groove of
the flywheel nut.

CUT AWAY FOR
MUFFLER OUTLET

Make 3mm holes as appropriate to
mount muffer support/protector.
Use HUDY Body Reamer
#107600

11~11.2 mm

FUEL TANK & ENGINE

It is very important that your XB808 has properly-adjusted
gear mesh. Adjust the gear mesh so there is adequate (or
slightly larger) space between the spur gear and clutchbell
teeth. Adjust the gear mesh by sliding the engine mounts in
the slots of the chassis. You should be able to rock one gear
back and forth slightly while holding the other one firmly. Be
sure to check the gear mesh all the way around the spur gear.
Tighten the screws once the engine alignment and gear mesh
are correct, and then re-check the gear mesh to ensure the
engine mounts did not move.

DETAIL

Tighten the clutch
nut using HUDY
tool #107581

Hold the flywheel using HUDY
Flywheel Tool #182010

4x10

3x16

3x10

DETAIL

4x10

4x5

3x8

DETAIL

3x12

Please note that the engine is not parallel with the chassis centerline, so that the
clutchbell engages the spur gear at a slight angle. This is correct and will not have any
effect on handling, performance, or lifespan of any parts.

DETAIL

DETAIL

Use the cone included
with your engine, or
use optional XRAY cone
#358540

NOTE ORIENTATION

Not using these shims may

cause that the flywheel pins will
press out after some time.

Although the XB808 clutch
bearings are oversized and have

a longer lifespan than regular-sized
ball-bearings, the bearings must still
be regularly serviced and replaced
when worn out.

IMPORTANT

ANGLED ENGINE POSITION

EXTREMELY IMPORTANT

CORRECT

«
...
25
26
27
28
29
...
»

Summary of Contents for XB808









































Reviews:

No comments

Related manuals for XB808

Brand: Xray Pages: 48

Brand: Tamiya Pages: 24

Brand: Tamiya Pages: 29

TT-02 White Special

Brand: Tamiya Pages: 24

LOWRIDE PUMPKIN

Brand: Tamiya Pages: 28

CADILLAC ESCALADE CUSTOM EDITION N8417

Brand: Power Wheels Pages: 32

Brand: Land of B. Pages: 2

SHELBY COBRA 427 S/C

Brand: Agora Models Pages: 35

XXX-NT Sport Ready-to-Run

Brand: Team Losi Pages: 2

Brand: Carson Pages: 44

STUNT CAR STEEL MONSTER

Brand: Revell Control Pages: 2

MINI COOPER S Foot To Floor

Brand: Rollplay Pages: 16

Brand: Rollplay Pages: 16

Brand: Brookstone Pages: 20

Brand: Jamara Pages: 12

The Scopion King Ford Monster Truck

Brand: REVELL Pages: 4

SnapTite SCOOBY-DOO! The Mystery Machine

Brand: REVELL Pages: 4

Brand: Corally Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands