Xray XB808 Instruction Manual Download Page 18

Page: 18 / 40

CASTER

TRACK WIDTH

902414

SH M4x14

Use HUDY Ball-Bearing

Grease for servicing:

#106220 - Standard
#106221 - Extra
#106222 - Premium

➊

➋

➊

980317

P 3x17

941319

BB 13x19x4

901504

SB M5x4

980263

P 2.5x13

940814

BB 8x14x4

6. FRONT SUSPENSION

35 2151

XB808 FRONT UPPER ARM BALL JOINT (2)

35 2181

XB808 STEEL ARM BUSHING (2)

35 2212

XB808 COMPOSITE CASTER BLOCK 10° RIGHT

35 2222

XB808 COMPOSITE CASTER BLOCK 10° LEFT

35 2252

XB808 COMPOSITE STEERING BLOCK RIGHT

35 2262

XB808 COMPOSITE STEERING BLOCK LEFT

35 2299

XB808 STEEL STEERING BUSHING (2)

35 2621

ADJ. TURNBUCKLE M5 L/R 58 MM - HUDY SPRING STEEL (2)

35 3160

MOUNTING BALL 6.8 (4)

35 3170

PIVOT BALL 6.8 (4)

35 5211

XB808 CVD DRIVE AXLE - HUDY SPRING STEEL™

35 5221

XB808 CVD UNIVERSAL DRIVE SHAFT - HUDY SPRING STEEL™

35 5237

XB808 CVD DRIVE SHAFT COUPLING - HUDY SPRING STEEL™

35 5250

ALU WHEEL AXLE - HARD COATED (2)

90 1504

HEX SCREW SB M5x4 (10)

90 2316

HEX SCREW SH M3x16 (10)

90 2325

HEX SCREW SH M3x25 (10)

90 2414

HEX SCREW SH M4x14 (10)

90 2418

HEX SCREW SH M4x18 (10)

94 0814

HIGH-SPEED BALL-BEARING 8x14x4 BLUE COVERED (2)

94 1319

HIGH-SPEED BALL-BEARING 13x19x4 BLUE COVERED (2)

96 0030

NUT M3 (10)

98 0263

PIN 2.5x13 (10)

98 0317

PIN 3x17 (10)

BAG

353170

352621

902316

➎

➍

➏

➐

➑

Graphite Grease

(HUDY #106210)

Marked “R“

353160

352151

960030

902418

901504

902418

960030

352181

355221

980263

902414

355237

355211

941319

352252

352299

940814

980317

355250

352212

Marked “R“

➌

352151

902325

352222

352262

3x17

2.5x13

8x14x4

13x19x4

To tighten the setscrew you can also use
HUDY 17mm Wheel Nut Tool #107570

Follow the TECH TIP on page 5
for drive shaft pin servicing

CASTER BLOCKS

#352212

10° - RIGHT (STANDARD)

#352213

12° - RIGHT (OPTION)

#352214

14° - RIGHT (OPTION)

#352222

10° - LEFT (STANDARD)

#352223

12° - LEFT (OPTION)

#352224

14° - LEFT (OPTION)

OFFSET WHEEL AXLES

#355250

0mm (STANDARD)

#355251

+1mm (OPTION)

#355252

+2mm (OPTION)

DO NOT

OVERTIGHTEN

➌

DO NOT
OVERTIGHTEN

The standard caster block features
10° caster angle and together with
the 10° angle of the chassis creates
a total 20° caster.

Marked “L“

ASSEMBLED VIEW

Check for free
movement

2.5mm

Summary of Contents for XB808









































Search results

Summary of Contents for XB808

Reviews:

Related manuals for XB808

Brands by name

Popular brands

Xray XB808, Instruction Manual

Search results

Summary of Contents for XB808

Reviews:

Related manuals for XB808

Brands by name

Popular brands