Xray XB808 Instruction Manual Download Page 9

Page: 9 / 40

GEAR DIFF

After assembly the differential should have
a length of 32.6~32.7 mm measured from
the ends of the installed ball-bearings. If
differential is longer, retighten the 4 screws
holding the spur gear.

32.6~32.7 mm

➊

➋

➍

➎

➏

➌

➐

940814

BB 8x14x4

971060

O 6x1.5

964060

S 6x18x0.2

Center diff:

Silicone oil

7000cSt

Fill just above the
satellite gears.

980212

P 2x11.6

VERY IMPORTANT!

Fill the differentials with oil just
above the satellite gears.

OIL

INCORRECT

CORRECT

CENTER DIFFERENTIAL

964030

S 3.5x12x0.2

903312

SFH M3x12

Tighten the screws equally

Finish tightening in this order

OIL

➊

➋

➌

➍

STEP DETAIL

➏

Use HUDY Ball-Bearing

Grease for servicing:

#106220 - Standard
#106221 - Extra
#106222 - Premium

Use the following silicone oil included in the kit for initial setting:

Center diff:

7000cSt

Graphite Grease

(HUDY #106210)

Graphite Grease

(HUDY #106210)

Summary of Contents for XB808









































Search results

Summary of Contents for XB808

Reviews:

Related manuals for XB808

Brands by name

Popular brands

Xray XB808, Instruction Manual

Search results

Summary of Contents for XB808

Reviews:

Related manuals for XB808

Brands by name

Popular brands