background image

Part Number

 

18141, F, 11/06/2017

 

 

Maintenance 
 
The system should be tested periodically in the fashion described in the previous sections.  Due to 
the harsh environmental conditions in marine applications, it is recommended to replace the 
Gasoline Fume Sensors every 3-4 years. 
 
In the Event of an Alarm 
 
Immediately have all passengers and crew exit the passenger compartment and vessel if possible.   
 
Ventilate the space being monitored. 
 
Carefully check all fuel lines and other potential sources of gasoline fume leaks.  If leaks are 
identified, shut off fuel supply and make any necessary repairs.   
 
Repairing Xintex Gasoline Fume Detection Components 
 
Xintex Gasoline Fume Detection Components are not field serviceable.  Components must be 
returned to the factory for any repairs. 
 
Returning Xintex Gasoline Detection Components 
 
No product may be returned for credit or repair without a written “Returned Material 
Authorization” (RMA) form.  Purchaser must call or email Fireboy-Xintex 616-735-9380 or 
[email protected] for a RMA.  If due to extenuating circumstances a product is to be 
returned, after approval it must be received in 100% new/resalable condition.  Products stored by 
the buyer for more than 26 weeks may not be returned for any reason.  Maintaining fresh and 
current inventory is the responsibility of the buyer. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for G-1BB-R










Reviews: